|
HTML rendering created 2024-06-26 by Michael Kerrisk, author of The Linux Programming Interface. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH. |
|
ovs-fields(7) Open vSwitch Manual ovs-fields(7)
ovs-fields - protocol header fields in OpenFlow and Open vSwitch
This document aims to comprehensively document all of the fields,
both standard and non-standard, supported by OpenFlow or Open
vSwitch, regardless of origin.
Fields
A field is a property of a packet. Most familiarly, data fields
are fields that can be extracted from a packet. Most data fields
are copied directly from protocol headers, e.g. at layer 2, the
Ethernet source and destination addresses, or the VLAN ID; at
layer 3, the IPv4 or IPv6 source and destination; and at layer 4,
the TCP or UDP ports. Other data fields are computed, e.g.
ip_frag describes whether a packet is a fragment but it is not
copied directly from the IP header.
Data fields that are always present as a consequence of the basic
networking technology in use are called called root fields. Open
vSwitch 2.7 and earlier considered Ethernet fields to be root
fields, and this remains the default mode of operation for Open
vSwitch bridges. When a packet is received from a non-Ethernet
interfaces, such as a layer-3 LISP tunnel, Open vSwitch 2.7 and
earlier force-fit the packet to this Ethernet-centric point of
view by pretending that an Ethernet header is present whose
Ethernet type that indicates the packet’s actual type (and whose
source and destination addresses are all-zero).
Open vSwitch 2.8 and later implement the ``packet type-aware
pipeline’’ concept introduced in OpenFlow 1.5. Such a pipeline
does not have any root fields. Instead, a new metadata field,
packet_type, indicates the basic type of the packet, which can be
Ethernet, IPv4, IPv6, or another type. For backward
compatibility, by default Open vSwitch 2.8 imitates the behavior
of Open vSwitch 2.7 and earlier. Later versions of Open vSwitch
may change the default, and in the meantime controllers can turn
off this legacy behavior, on a port-by-port basis, by setting
options:packet_type to ptap in the Interface table. This is
significant only for ports that can handle non-Ethernet packets,
which is currently just LISP, VXLAN-GPE, and GRE tunnel ports.
See ovs-vwitchd.conf.db(5) for more information.
Non-root data fields are not always present. A packet contains
ARP fields, for example, only when its packet type is ARP or when
it is an Ethernet packet whose Ethernet header indicates the
Ethertype for ARP, 0x0806. In this documentation, we say that a
field is applicable when it is present in a packet, and
inapplicable when it is not. (These are not standard terms.) We
refer to the conditions that determine whether a field is
applicable as prerequisites. Some VLAN-related fields are a
special case: these fields are always applicable for Ethernet
packets, but have a designated value or bit that indicates
whether a VLAN header is present, with the remaining values or
bits indicating the VLAN header’s content (if it is present).
An inapplicable field does not have a value, not even a nominal
``value’’ such as all-zero-bits. In many circumstances, OpenFlow
and Open vSwitch allow references only to applicable fields. For
example, one may match (see Matching, below) a given field only
if the match includes the field’s prerequisite, e.g. matching an
ARP field is only allowed if one also matches on Ethertype 0x0806
or the packet_type for ARP in a packet type-aware bridge.
Sometimes a packet may contain multiple instances of a header.
For example, a packet may contain multiple VLAN or MPLS headers,
and tunnels can cause any data field to recur. OpenFlow and Open
vSwitch do not address these cases uniformly. For VLAN and MPLS
headers, only the outermost header is accessible, so that inner
headers may be accessed only by ``popping’’ (removing) the outer
header. (Open vSwitch supports only a single VLAN header in any
case.) For tunnels, e.g. GRE or VXLAN, the outer header and inner
headers are treated as different data fields.
Many network protocols are built in layers as a stack of
concatenated headers. Each header typically contains a ``next
type’’ field that indicates the type of the protocol header that
follows, e.g. Ethernet contains an Ethertype and IPv4 contains a
IP protocol type. The exceptional cases, where protocols are
layered but an outer layer does not indicate the protocol type
for the inner layer, or gives only an ambiguous indication, are
troublesome. An MPLS header, for example, only indicates whether
another MPLS header or some other protocol follows, and in the
latter case the inner protocol must be known from the context. In
these exceptional cases, OpenFlow and Open vSwitch cannot provide
insight into the inner protocol data fields without additional
context, and thus they treat all later data fields as
inapplicable until an OpenFlow action explicitly specifies what
protocol follows. In the case of MPLS, the OpenFlow ``pop MPLS’’
action that removes the last MPLS header from a packet provides
this context, as the Ethertype of the payload. See Layer 2.5:
MPLS for more information.
OpenFlow and Open vSwitch support some fields other than data
fields. Metadata fields relate to the origin or treatment of a
packet, but they are not extracted from the packet data itself.
One example is the physical port on which a packet arrived at the
switch. Register fields act like variables: they give an OpenFlow
switch space for temporary storage while processing a packet.
Existing metadata and register fields have no prerequisites.
A field’s value consists of an integral number of bytes. For data
fields, sometimes those bytes are taken directly from the packet.
Other data fields are copied from a packet with padding (usually
with zeros and in the most significant positions). The remaining
data fields are transformed in other ways as they are copied from
the packets, to make them more useful for matching.
Matching
The most important use of fields in OpenFlow is matching, to
determine whether particular field values agree with a set of
constraints called a match. A match consists of zero or more
constraints on individual fields, all of which must be met to
satisfy the match. (A match that contains no constraints is
always satisfied.) OpenFlow and Open vSwitch support a number of
forms of matching on individual fields:
Exact match, e.g. nw_src=10.1.2.3
Only a particular value of the field is matched;
for example, only one particular source IP address.
Exact matches are written as field=value. The forms
accepted for value depend on the field.
All fields support exact matches.
Bitwise match, e.g. nw_src=10.1.0.0/255.255.0.0
Specific bits in the field must have specified
values; for example, only source IP addresses in a
particular subnet. Bitwise matches are written as
field=value/mask, where value and mask take one of
the forms accepted for an exact match on field.
Some fields accept other forms for bitwise matches;
for example, nw_src=10.1.0.0/255.255.0.0 may also
be written nw_src=10.1.0.0/16.
Most OpenFlow switches do not allow every bitwise
matching on every field (and before OpenFlow 1.2,
the protocol did not even provide for the
possibility for most fields). Even switches that do
allow bitwise matching on a given field may
restrict the masks that are allowed, e.g. by
allowing matches only on contiguous sets of bits
starting from the most significant bit, that is,
``CIDR’’ masks [RFC 4632]. Open vSwitch does not
allows bitwise matching on every field, but it
allows arbitrary bitwise masks on any field that
does support bitwise matching. (Older versions had
some restrictions, as documented in the
descriptions of individual fields.)
Wildcard, e.g. ``any nw_src’’
The value of the field is not constrained.
Wildcarded fields may be written as field=*,
although it is unusual to mention them at all.
(When specifying a wildcard explicitly in a command
invocation, be sure to using quoting to protect
against shell expansion.)
There is a tiny difference between wildcarding a
field and not specifying any match on a field:
wildcarding a field requires satisfying the field’s
prerequisites.
Some types of matches on individual fields cannot be expressed
directly with OpenFlow and Open vSwitch. These can be expressed
indirectly:
Set match, e.g. ``tcp_dst ∈ {80, 443, 8080}’’
The value of a field is one of a specified set of
values; for example, the TCP destination port is
80, 443, or 8080.
For matches used in flows (see Flows, below),
multiple flows can simulate set matches.
Range match, e.g. ``1000 ≤ tcp_dst ≤ 1999’’
The value of the field must lie within a numerical
range, for example, TCP destination ports between
1000 and 1999.
Range matches can be expressed as a collection of
bitwise matches. For example, suppose that the goal
is to match TCP source ports 1000 to 1999,
inclusive. The binary representations of 1000 and
1999 are:
01111101000
11111001111
The following series of bitwise matches will match
1000 and 1999 and all the values in between:
01111101xxx
0111111xxxx
10xxxxxxxxx
110xxxxxxxx
1110xxxxxxx
11110xxxxxx
1111100xxxx
which can be written as the following matches:
tcp,tp_src=0x03e8/0xfff8
tcp,tp_src=0x03f0/0xfff0
tcp,tp_src=0x0400/0xfe00
tcp,tp_src=0x0600/0xff00
tcp,tp_src=0x0700/0xff80
tcp,tp_src=0x0780/0xffc0
tcp,tp_src=0x07c0/0xfff0
Inequality match, e.g. ``tcp_dst ≠ 80’’
The value of the field differs from a specified
value, for example, all TCP destination ports
except 80.
An inequality match on an n-bit field can be
expressed as a disjunction of n 1-bit matches. For
example, the inequality match ``vlan_pcp ≠ 5’’ can
be expressed as ``vlan_pcp = 0/4 or vlan_pcp = 2/2
or vlan_pcp = 0/1.’’ For matches used in flows (see
Flows, below), sometimes one can more compactly
express inequality as a higher-priority flow that
matches the exceptional case paired with a lower-
priority flow that matches the general case.
Alternatively, an inequality match may be converted
to a pair of range matches, e.g. tcp_src ≠ 80 may
be expressed as ``0 ≤ tcp_src < 80 or 80 < tcp_src
≤ 65535’’, and then each range match may in turn be
converted to a bitwise match.
Conjunctive match, e.g. ``tcp_src ∈ {80, 443, 8080} and
tcp_dst ∈ {80, 443, 8080}’’
As an OpenFlow extension, Open vSwitch supports
matching on conditions on conjunctions of the
previously mentioned forms of matching. See the
documentation for conj_id for more information.
All of these supported forms of matching are special cases of
bitwise matching. In some cases this influences the design of
field values. ip_frag is the most prominent example: it is
designed to make all of the practically useful checks for IP
fragmentation possible as a single bitwise match.
Shorthands
Some matches are very commonly used, so Open vSwitch accepts
shorthand notations. In some cases, Open vSwitch also uses
shorthand notations when it displays matches. The following
shorthands are defined, with their long forms shown on the right
side:
eth packet_type=(0,0) (Open vSwitch 2.8 and later)
ip eth_type=0x0800
ipv6 eth_type=0x86dd
icmp eth_type=0x0800,ip_proto=1
icmp6 eth_type=0x86dd,ip_proto=58
tcp eth_type=0x0800,ip_proto=6
tcp6 eth_type=0x86dd,ip_proto=6
udp eth_type=0x0800,ip_proto=17
udp6 eth_type=0x86dd,ip_proto=17
sctp eth_type=0x0800,ip_proto=132
sctp6 eth_type=0x86dd,ip_proto=132
arp eth_type=0x0806
rarp eth_type=0x8035
mpls eth_type=0x8847
mplsm eth_type=0x8848
Evolution of OpenFlow Fields
The discussion so far applies to all OpenFlow and Open vSwitch
versions. This section starts to draw in specific information by
explaining, in broad terms, the treatment of fields and matches
in each OpenFlow version.
OpenFlow 1.0
OpenFlow 1.0 defined the OpenFlow protocol format of a match as a
fixed-length data structure that could match on the following
fields:
• Ingress port.
• Ethernet source and destination MAC.
• Ethertype (with a special value to match frames
that lack an Ethertype).
• VLAN ID and priority.
• IPv4 source, destination, protocol, and DSCP.
• TCP source and destination port.
• UDP source and destination port.
• ICMPv4 type and code.
• ARP IPv4 addresses (SPA and TPA) and opcode.
Each supported field corresponded to some member of the data
structure. Some members represented multiple fields, in the case
of the TCP, UDP, ICMPv4, and ARP fields whose presence is
mutually exclusive. This also meant that some members were poor
fits for their fields: only the low 8 bits of the 16-bit ARP
opcode could be represented, and the ICMPv4 type and code were
padded with 8 bits of zeros to fit in the 16-bit members
primarily meant for TCP and UDP ports. An additional bitmap
member indicated, for each member, whether its field should be an
``exact’’ or ``wildcarded’’ match (see Matching), with additional
support for CIDR prefix matching on the IPv4 source and
destination fields.
Simplicity was recognized early on as the main virtue of this
approach. Obviously, any fixed-length data structure cannot
support matching new protocols that do not fit. There was no
room, for example, for matching IPv6 fields, which was not a
priority at the time. Lack of room to support matching the
Ethernet addresses inside ARP packets actually caused more of a
design problem later, leading to an Open vSwitch extension action
specialized for dropping ``spoofed’’ ARP packets in which the
frame and ARP Ethernet source addressed differed. (This extension
was never standardized. Open vSwitch dropped support for it a few
releases after it added support for full ARP matching.)
The design of the OpenFlow fixed-length matches also illustrates
compromises, in both directions, between the strengths and
weaknesses of software and hardware that have always influenced
the design of OpenFlow. Support for matching ARP fields that do
fit in the data structure was only added late in the design
process (and remained optional in OpenFlow 1.0), for example,
because common switch ASICs did not support matching these
fields.
The compromises in favor of software occurred for more
complicated reasons. The OpenFlow designers did not know how to
implement matching in software that was fast, dynamic, and
general. (A way was later found [Srinivasan].) Thus, the
designers sought to support dynamic, general matching that would
be fast in realistic special cases, in particular when all of the
matches were microflows, that is, matches that specify every
field present in a packet, because such matches can be
implemented as a single hash table lookup. Contemporary research
supported the feasibility of this approach: the number of
microflows in a campus network had been measured to peak at about
10,000 [Casado, section 3.2]. (Calculations show that this can
only be true in a lightly loaded network [Pepelnjak].)
As a result, OpenFlow 1.0 required switches to treat microflow
matches as the highest possible priority. This let software
switches perform the microflow hash table lookup first. Only on
failure to match a microflow did the switch need to fall back to
checking the more general and presumed slower matches. Also, the
OpenFlow 1.0 flow match was minimally flexible, with no support
for general bitwise matching, partly on the basis that this
seemed more likely amenable to relatively efficient software
implementation. (CIDR masking for IPv4 addresses was added
relatively late in the OpenFlow 1.0 design process.)
Microflow matching was later discovered to aid some hardware
implementations. The TCAM chips used for matching in hardware do
not support priority in the same way as OpenFlow but instead tie
priority to ordering [Pagiamtzis]. Thus, adding a new match with
a priority between the priorities of existing matches can require
reordering an arbitrary number of TCAM entries. On the other
hand, when microflows are highest priority, they can be managed
as a set-aside portion of the TCAM entries.
The emphasis on matching microflows also led designers to
carefully consider the bandwidth requirements between switch and
controller: to maximize the number of microflow setups per
second, one must minimize the size of each flow’s description.
This favored the fixed-length format in use, because it expressed
common TCP and UDP microflows in fewer bytes than more flexible
``type-length-value’’ (TLV) formats. (Early versions of OpenFlow
also avoided TLVs in general to head off protocol fragmentation.)
Inapplicable Fields
OpenFlow 1.0 does not clearly specify how to treat inapplicable
fields. The members for inapplicable fields are always present in
the match data structure, as are the bits that indicate whether
the fields are matched, and the ``correct’’ member and bit values
for inapplicable fields is unclear. OpenFlow 1.0 implementations
changed their behavior over time as priorities shifted. The early
OpenFlow reference implementation, motivated to make every flow a
microflow to enable hashing, treated inapplicable fields as exact
matches on a value of 0. Initially, this behavior was implemented
in the reference controller only.
Later, the reference switch was also changed to actually force
any wildcarded inapplicable fields into exact matches on 0. The
latter behavior sometimes caused problems, because the modified
flow was the one reported back to the controller later when it
queried the flow table, and the modifications sometimes meant
that the controller could not properly recognize the flow that it
had added. In retrospect, perhaps this problem should have
alerted the designers to a design error, but the ability to use a
single hash table was held to be more important than almost every
other consideration at the time.
When more flexible match formats were introduced much later, they
disallowed any mention of inapplicable fields as part of a match.
This raised the question of how to translate between this new
format and the OpenFlow 1.0 fixed format. It seemed somewhat
inconsistent and backward to treat fields as exact-match in one
format and forbid matching them in the other, so instead the
treatment of inapplicable fields in the fixed-length format was
changed from exact match on 0 to wildcarding. (A better
classifier had by now eliminated software performance problems
with wildcards.)
The OpenFlow 1.0.1 errata (released only in 2012) added some
additional explanation [OpenFlow 1.0.1, section 3.4], but it did
not mandate specific behavior because of variation among
implementations.
OpenFlow 1.1
The OpenFlow 1.1 protocol match format was designed as a
type/length/value (TLV) format to allow for future flexibility.
The specification standardized only a single type OFPMT_STANDARD
(0) with a fixed-size payload, described here. The additional
fields and bitwise masks in OpenFlow 1.1 cause this match
structure to be over twice as large as in OpenFlow 1.0, 88 bytes
versus 40.
OpenFlow 1.1 added support for the following fields:
• SCTP source and destination port.
• MPLS label and traffic control (TC) fields.
• One 64-bit register (named ``metadata’’).
OpenFlow 1.1 increased the width of the ingress port number field
(and all other port numbers in the protocol) from 16 bits to 32
bits.
OpenFlow 1.1 increased matching flexibility by introducing
arbitrary bitwise matching on Ethernet and IPv4 address fields
and on the new ``metadata’’ register field. Switches were not
required to support all possible masks [OpenFlow 1.1, section
4.3].
By a strict reading of the specification, OpenFlow 1.1 removed
support for matching ICMPv4 type and code [OpenFlow 1.1, section
A.2.3], but this is likely an editing error because ICMP matching
is described elsewhere [OpenFlow 1.1, Table 3, Table 4, Figure
4]. Open vSwitch does support ICMPv4 type and code matching with
OpenFlow 1.1.
OpenFlow 1.1 avoided the pitfalls of inapplicable fields that
OpenFlow 1.0 encountered, by requiring the switch to ignore the
specified field values [OpenFlow 1.1, section A.2.3]. It also
implied that the switch should ignore the bits that indicate
whether to match inapplicable fields.
Physical Ingress Port
OpenFlow 1.1 introduced a new pseudo-field, the physical ingress
port. The physical ingress port is only a pseudo-field because it
cannot be used for matching. It appears only one place in the
protocol, in the ``packet-in’’ message that passes a packet
received at the switch to an OpenFlow controller.
A packet’s ingress port and physical ingress port are identical
except for packets processed by a switch feature such as bonding
or tunneling that makes a packet appear to arrive on a
``virtual’’ port associated with the bond or the tunnel. For such
packets, the ingress port is the virtual port and the physical
ingress port is, naturally, the physical port. Open vSwitch
implements both bonding and tunneling, but its bonding
implementation does not use virtual ports and its tunnels are
typically not on the same OpenFlow switch as their physical
ingress ports (which need not be part of any switch), so the
ingress port and physical ingress port are always the same in
Open vSwitch.
OpenFlow 1.2
OpenFlow 1.2 abandoned the fixed-length approach to matching. One
reason was size, since adding support for IPv6 address matching
(now seen as important), with bitwise masks, would have added 64
bytes to the match length, increasing it from 88 bytes in
OpenFlow 1.1 to over 150 bytes. Extensibility had also become
important as controller writers increasingly wanted support for
new fields without having to change messages throughout the
OpenFlow protocol. The challenges of carefully defining fixed-
length matches to avoid problems with inapplicable fields had
also become clear over time.
Therefore, OpenFlow 1.2 adopted a flow format using a flexible
type-length-value (TLV) representation, in which each TLV
expresses a match on one field. These TLVs were in turn
encapsulated inside the outer TLV wrapper introduced in OpenFlow
1.1 with the new identifier OFPMT_OXM (1). (This wrapper
fulfilled its intended purpose of reducing the amount of churn in
the protocol when changing match formats; some messages that
included matches remained unchanged from OpenFlow 1.1 to 1.2 and
later versions.)
OpenFlow 1.2 added support for the following fields:
• ARP hardware addresses (SHA and THA).
• IPv4 ECN.
• IPv6 source and destination addresses, flow label,
DSCP, ECN, and protocol.
• TCP, UDP, and SCTP port numbers when encapsulated
inside IPv6.
• ICMPv6 type and code.
• ICMPv6 Neighbor Discovery target address and source
and target Ethernet addresses.
The OpenFlow 1.2 format, called OXM (OpenFlow Extensible Match),
was modeled closely on an extension to OpenFlow 1.0 introduced in
Open vSwitch 1.1 called NXM (Nicira Extended Match). Each OXM or
NXM TLV has the following format:
type
<---------------->
16 7 1 8 length bytes
+------------+-----+--+------+ +------------+
|vendor/class|field|HM|length| | body |
+------------+-----+--+------+ +------------+
The most significant 16 bits of the NXM or OXM header, called
vendor by NXM and class by OXM, identify an organization
permitted to allocate identifiers for fields. NXM allocates only
two vendors, 0x0000 for fields supported by OpenFlow 1.0 and
0x0001 for fields implemented as an Open vSwitch extension. OXM
assigns classes as follows:
0x0000 (OFPXMC_NXM_0).
0x0001 (OFPXMC_NXM_1).
Reserved for NXM compatibility.
0x0002 to 0x7fff
Reserved for allocation to ONF members, but none yet
assigned.
0x8000 (OFPXMC_OPENFLOW_BASIC)
Used for most standard OpenFlow fields.
0x8001 (OFPXMC_PACKET_REGS)
Used for packet register fields in OpenFlow 1.5 and
later.
0x8002 to 0xfffe
Reserved for the OpenFlow specification.
0xffff (OFPXMC_EXPERIMENTER)
Experimental use.
When class is 0xffff, the OXM header is extended to 64 bits by
using the first 32 bits of the body as an experimenter field
whose most significant byte is zero and whose remaining bytes are
an Organizationally Unique Identifier (OUI) assigned by the IEEE
[IEEE OUI], as shown below.
type experimenter
<----------> <---------->
16 7 1 8 8 24 (length - 4) bytes
+------+-----+--+------+ +------+-----+ +------------------+
|class |field|HM|length| | zero | OUI | | body |
+------+-----+--+------+ +------+-----+ +------------------+
0xffff 0x00
OpenFlow says that support for experimenter fields is optional.
Open vSwitch 2.4 and later does support them, so that it can
support the following experimenter classes:
0x4f4e4600 (ONFOXM_ET)
Used by official Open Networking Foundation
extensions in OpenFlow 1.3 and later. e.g. [TCP
Flags Match Field Extension].
0x005ad650 (NXOXM_NSH)
Used by Open vSwitch for NSH extensions, in the
absence of an official ONF-assigned class. (This
OUI is randomly generated.)
Taken as a unit, class (or vendor), field, and experimenter (when
present) uniquely identify a particular field.
When hasmask (abbreviated HM above) is 0, the OXM is an exact
match on an entire field. In this case, the body (excluding the
experimenter field, if present) is a single value to be matched.
When hasmask is 1, the OXM is a bitwise match. The body
(excluding the experimenter field) consists of a value to match,
followed by the bitwise mask to apply. A 1-bit in the mask
indicates that the corresponding bit in the value should be
matched and a 0-bit that it should be ignored. For example, for
an IP address field, a value of 192.168.0.0 followed by a mask of
255.255.0.0 would match addresses in the 196.168.0.0/16 subnet.
• Some fields might not support masking at all, and
some fields that do support masking might restrict
it to certain patterns. For example, fields that
have IP address values might be restricted to CIDR
masks. The descriptions of individual fields note
these restrictions.
• An OXM TLV with a mask that is all zeros is not
useful (although it is not forbidden), because it
is has the same effect as omitting the TLV
entirely.
• It is not meaningful to pair a 0-bit in an OXM mask
with a 1-bit in its value, and Open vSwitch rejects
such an OXM with the error OFPBMC_BAD_WILDCARDS, as
required by OpenFlow 1.3 and later.
The length identifies the number of bytes in the body, including
the 4-byte experimenter header, if it is present. Each OXM TLV
has a fixed length; that is, given class, field, experimenter (if
present), and hasmask, length is a constant. The length is
included explicitly to allow software to minimally parse OXM TLVs
of unknown types.
OXM TLVs must be ordered so that a field’s prerequisites are
satisfied before it is parsed. For example, an OXM TLV that
matches on the IPv4 source address field is only allowed
following an OXM TLV that matches on the Ethertype for IPv4.
Similarly, an OXM TLV that matches on the TCP source port must
follow a TLV that matches an Ethertype of IPv4 or IPv6 and one
that matches an IP protocol of TCP (in that order). The order of
OXM TLVs is not otherwise restricted; no canonical ordering is
defined.
A given field may be matched only once in a series of OXM TLVs.
OpenFlow 1.3
OpenFlow 1.3 showed OXM to be largely successful, by adding new
fields without making any changes to how flow matches otherwise
worked. It added OXMs for the following fields supported by Open
vSwitch:
• Tunnel ID for ports associated with e.g. VXLAN or
keyed GRE.
• MPLS ``bottom of stack’’ (BOS) bit.
OpenFlow 1.3 also added OXMs for the following fields not
documented here and not yet implemented by Open vSwitch:
• IPv6 extension header handling.
• PBB I-SID.
OpenFlow 1.4
OpenFlow 1.4 added OXMs for the following fields not documented
here and not yet implemented by Open vSwitch:
• PBB UCA.
OpenFlow 1.5
OpenFlow 1.5 added OXMs for the following fields supported by
Open vSwitch:
• Packet type.
• TCP flags.
• Packet registers.
• The output port in the OpenFlow action set.
The following sections document the fields that Open vSwitch
supports. Each section provides introductory material on a group
of related fields, followed by information on each individual
field. In addition to field-specific information, each field
begins with a table with entries for the following important
properties:
Name The field’s name, used for parsing and formatting
the field, e.g. in ovs-ofctl commands. For
historical reasons, some fields have an additional
name that is accepted as an alternative in parsing.
This name, when there is one, is listed as well,
e.g. ``tun (aka tunnel_id).’’
Width The field’s width, always a multiple of 8 bits.
Some fields don’t use all of the bits, so this may
be accompanied by an explanation. For example,
OpenFlow embeds the 2-bit IP ECN field as as the
low bits in an 8-bit byte, and so its width is
expressed as ``8 bits (only the least-significant 2
bits may be nonzero).’’
Format How a value for the field is formatted or parsed
by, e.g., ovs-ofctl. Some possibilities are
generic:
decimal
Formats as a decimal number. On input,
accepts decimal numbers or hexadecimal
numbers prefixed by 0x.
hexadecimal
Formats as a hexadecimal number prefixed by
0x. On input, accepts decimal numbers or
hexadecimal numbers prefixed by 0x. (The
default for parsing is not hexadecimal: only
a 0x prefix causes input to be treated as
hexadecimal.)
Ethernet
Formats and accepts the common Ethernet
address format xx:xx:xx:xx:xx:xx.
IPv4 Formats and accepts the dotted-quad format
a.b.c.d. For bitwise matches, formats and
accepts address/length CIDR notation in
addition to address/mask.
IPv6 Formats and accepts the common IPv6 address
formats, plus CIDR notation for bitwise
matches.
OpenFlow 1.0 port
Accepts 16-bit port numbers in decimal, plus
OpenFlow well-known port names (e.g.
IN_PORT) in uppercase or lowercase.
OpenFlow 1.1+ port
Same syntax as OpenFlow 1.0 ports but for
32-bit OpenFlow 1.1+ port number fields.
Other, field-specific formats are explained along
with their fields.
Masking
For most fields, this says ``arbitrary bitwise
masks,’’ meaning that a flow may match any
combination of bits in the field. Some fields
instead say ``exact match only,’’ which means that
a flow that matches on this field must match on the
whole field instead of just certain bits. Either
way, this reports masking support for the latest
version of Open vSwitch using OXM or NXM (that is,
either OpenFlow 1.2+ or OpenFlow 1.0 plus Open
vSwitch NXM extensions). In particular, OpenFlow
1.0 (without NXM) and 1.1 don’t always support
masking even if Open vSwitch itself does; refer to
the OpenFlow 1.0 and OpenFlow 1.1 rows to learn
about masking with these protocol versions.
Prerequisites
Requirements that must be met to match on this
field. For example, ip_src has IPv4 as a
prerequisite, meaning that a match must include
eth_type=0x0800 to match on the IPv4 source
address. The following prerequisites, with their
requirements, are currently in use:
none (no requirements)
VLAN VID
vlan_tci=0x1000/0x1000 (i.e. a VLAN header
is present)
ARP eth_type=0x0806 (ARP) or eth_type=0x8035
(RARP)
IPv4 eth_type=0x0800
IPv6 eth_type=0x86dd
IPv4/IPv6
IPv4 or IPv6
MPLS eth_type=0x8847 or eth_type=0x8848
TCP IPv4/IPv6 and ip_proto=6
UDP IPv4/IPv6 and ip_proto=17
SCTP IPv4/IPv6 and ip_proto=132
ICMPv4 IPv4 and ip_proto=1
ICMPv6 IPv6 and ip_proto=58
ND solicit
ICMPv6 and icmp_type=135 and icmp_code=0
ND advert
ICMPv6 and icmp_type=136 and icmp_code=0
ND ND solicit or ND advert
The TCP, UDP, and SCTP prerequisites also have the
special requirement that nw_frag is not being used
to select ``later fragments.’’ This is because only
the first fragment of a fragmented IPv4 or IPv6
datagram contains the TCP or UDP header.
Access Most fields are ``read/write,’’ which means that
common OpenFlow actions like set_field can modify
them. Fields that are ``read-only’’ cannot be
modified in these general-purpose ways, although
there may be other ways that actions can modify
them.
OpenFlow 1.0
OpenFlow 1.1
These rows report the level of support that OpenFlow
1.0 or OpenFlow 1.1, respectively, has for a field.
For OpenFlow 1.0, supported fields are reported as
either ``yes (exact match only)’’ for fields that do
not support any bitwise masking or ``yes (CIDR match
only)’’ for fields that support CIDR masking.
OpenFlow 1.1 supported fields report either ``yes
(exact match only)’’ or simply ``yes’’ for fields
that do support arbitrary masks. These OpenFlow
versions supported a fixed collection of fields that
cannot be extended, so many more fields are reported
as ``not supported.’’
OXM
NXM These rows report the OXM and NXM code points that
correspond to a given field. Either or both may be
``none.’’
A field that has only an OXM code point is usually
one that was standardized before it was added to Open
vSwitch. A field that has only an NXM code point is
usually one that is not yet standardized. When a
field has both OXM and NXM code points, it usually
indicates that it was introduced as an Open vSwitch
extension under the NXM code point, then later
standardized under the OXM code point. A field can
have more than one OXM code point if it was
standardized in OpenFlow 1.4 or later and
additionally introduced as an official ONF extension
for OpenFlow 1.3. (A field that has neither OXM nor
NXM code point is typically an obsolete field that is
supported in some other form using OXM or NXM.)
Each code point in these rows is described in the
form ``NAME (number) since OpenFlow spec and Open
vSwitch version,’’ e.g. ``OXM_OF_ETH_TYPE (5) since
OpenFlow 1.2 and Open vSwitch 1.7.’’ First, NAME,
which specifies a name for the code point, starts
with a prefix that designates a class and, in some
cases, a vendor, as listed in the following table:
Prefix Vendor Class
─────────────── ─────────── ───────
NXM_OF (none) 0x0000
NXM_NX (none) 0x0001
ERICOXM_OF (none) 0x1000
OXM_OF (none) 0x8000
OXM_OF_PKT_REG (none) 0x8001
NXOXM_ET 0x00002320 0xffff
NXOXM_NSH 0x005ad650 0xffff
ONFOXM_ET 0x4f4e4600 0xffff
For more information on OXM/NXM classes and vendors,
refer back to OpenFlow 1.2 under Evolution of
OpenFlow Fields. The number is the field number
within the class and vendor. The OpenFlow spec is the
version of OpenFlow that standardized the code point.
It is omitted for NXM code points because they are
nonstandard. The version is the version of Open
vSwitch that first supported the code point.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
──────── ────── ───── ──── ──────── ────────────────
conj_id 4 no no none OVS 2.4+
An individual OpenFlow flow can match only a single value for
each field. However, situations often arise where one wants to
match one of a set of values within a field or fields. For
matching a single field against a set, it is straightforward and
efficient to add multiple flows to the flow table, one for each
value in the set. For example, one might use the following flows
to send packets with IP source address a, b, c, or d to the
OpenFlow controller:
ip,ip_src=a actions=controller
ip,ip_src=b actions=controller
ip,ip_src=c actions=controller
ip,ip_src=d actions=controller
Similarly, these flows send packets with IP destination address
e, f, g, or h to the OpenFlow controller:
ip,ip_dst=e actions=controller
ip,ip_dst=f actions=controller
ip,ip_dst=g actions=controller
ip,ip_dst=h actions=controller
Installing all of the above flows in a single flow table yields a
disjunctive effect: a packet is sent to the controller if ip_src
∈ {a,b,c,d} or ip_dst ∈ {e,f,g,h} (or both). (Pedantically, if
both of the above sets of flows are present in the flow table,
they should have different priorities, because OpenFlow says that
the results are undefined when two flows with same priority can
both match a single packet.)
Suppose, on the other hand, one wishes to match conjunctively,
that is, to send a packet to the controller only if both ip_src ∈
{a,b,c,d} and ip_dst ∈ {e,f,g,h}. This requires 4 × 4 = 16 flows,
one for each possible pairing of ip_src and ip_dst. That is
acceptable for our small example, but it does not gracefully
extend to larger sets or greater numbers of dimensions.
The conjunction action is a solution for conjunctive matches that
is built into Open vSwitch. A conjunction action ties groups of
individual OpenFlow flows into higher-level ``conjunctive
flows’’. Each group corresponds to one dimension, and each flow
within the group matches one possible value for the dimension. A
packet that matches one flow from each group matches the
conjunctive flow.
To implement a conjunctive flow with conjunction, assign the
conjunctive flow a 32-bit id, which must be unique within an
OpenFlow table. Assign each of the n ≥ 2 dimensions a unique
number from 1 to n; the ordering is unimportant. Add one flow to
the OpenFlow flow table for each possible value of each dimension
with conjunction(id, k/n) as the flow’s actions, where k is the
number assigned to the flow’s dimension. Together, these flows
specify the conjunctive flow’s match condition. When the
conjunctive match condition is met, Open vSwitch looks up one
more flow that specifies the conjunctive flow’s actions and
receives its statistics. This flow is found by setting conj_id to
the specified id and then again searching the flow table.
The following flows provide an example. Whenever the IP source is
one of the values in the flows that match on the IP source
(dimension 1 of 2), and the IP destination is one of the values
in the flows that match on IP destination (dimension 2 of 2),
Open vSwitch searches for a flow that matches conj_id against the
conjunction ID (1234), finding the first flow listed below.
conj_id=1234 actions=controller
ip,ip_src=10.0.0.1 actions=conjunction(1234, 1/2)
ip,ip_src=10.0.0.4 actions=conjunction(1234, 1/2)
ip,ip_src=10.0.0.6 actions=conjunction(1234, 1/2)
ip,ip_src=10.0.0.7 actions=conjunction(1234, 1/2)
ip,ip_dst=10.0.0.2 actions=conjunction(1234, 2/2)
ip,ip_dst=10.0.0.5 actions=conjunction(1234, 2/2)
ip,ip_dst=10.0.0.7 actions=conjunction(1234, 2/2)
ip,ip_dst=10.0.0.8 actions=conjunction(1234, 2/2)
Many subtleties exist:
• In the example above, every flow in a single
dimension has the same form, that is, dimension 1
matches on ip_src and dimension 2 on ip_dst, but
this is not a requirement. Different flows within a
dimension may match on different bits within a
field (e.g. IP network prefixes of different
lengths, or TCP/UDP port ranges as bitwise
matches), or even on entirely different fields
(e.g. to match packets for TCP source port 80 or
TCP destination port 80).
• The flows within a dimension can vary their matches
across more than one field, e.g. to match only
specific pairs of IP source and destination
addresses or L4 port numbers.
• A flow may have multiple conjunction actions, with
different id values. This is useful for multiple
conjunctive flows with overlapping sets. If one
conjunctive flow matches packets with both ip_src ∈
{a,b} and ip_dst ∈ {d,e} and a second conjunctive
flow matches ip_src ∈ {b,c} and ip_dst ∈ {f,g}, for
example, then the flow that matches ip_src=b would
have two conjunction actions, one for each
conjunctive flow. The order of conjunction actions
within a list of actions is not significant.
• A flow with conjunction actions may also include
note actions for annotations, but not any other
kind of actions. (They would not be useful because
they would never be executed.)
• All of the flows that constitute a conjunctive flow
with a given id must have the same priority. (Flows
with the same id but different priorities are
currently treated as different conjunctive flows,
that is, currently id values need only be unique
within an OpenFlow table at a given priority. This
behavior isn’t guaranteed to stay the same in later
releases, so please use id values unique within an
OpenFlow table.)
• Conjunctive flows must not overlap with each other,
at a given priority, that is, any given packet must
be able to match at most one conjunctive flow at a
given priority. Overlapping conjunctive flows yield
unpredictable results. (The flows that constitute a
conjunctive flow may overlap with those that
constitute the same or another conjunctive flow.)
• Following a conjunctive flow match, the search for
the flow with conj_id=id is done in the same
general-purpose way as other flow table searches,
so one can use flows with conj_id=id to act
differently depending on circumstances. (One
exception is that the search for the conj_id=id
flow itself ignores conjunctive flows, to avoid
recursion.) If the search with conj_id=id fails,
Open vSwitch acts as if the conjunctive flow had
not matched at all, and continues searching the
flow table for other matching flows.
• OpenFlow prerequisite checking occurs for the flow
with conj_id=id in the same way as any other flow,
e.g. in an OpenFlow 1.1+ context, putting a
mod_nw_src action into the example above would
require adding an ip match, like this:
conj_id=1234,ip actions=mod_nw_src:1.2.3.4,controller
• OpenFlow prerequisite checking also occurs for the
individual flows that comprise a conjunctive match
in the same way as any other flow.
• The flows that constitute a conjunctive flow do not
have useful statistics. They are never updated with
byte or packet counts, and so on. (For such a flow,
therefore, the idle and hard timeouts work much the
same way.)
• Sometimes there is a choice of which flows include
a particular match. For example, suppose that we
added an extra constraint to our example, to match
on ip_src ∈ {a,b,c,d} and ip_dst ∈ {e,f,g,h} and
tcp_dst = i. One way to implement this is to add
the new constraint to the conj_id flow, like this:
conj_id=1234,tcp,tcp_dst=i actions=mod_nw_src:1.2.3.4,controller
but this is not recommended because of the cost of
the extra flow table lookup. Instead, add the
constraint to the individual flows, either in one
of the dimensions or (slightly better) all of them.
• A conjunctive match must have n ≥ 2 dimensions
(otherwise a conjunctive match is not necessary).
Open vSwitch enforces this.
• Each dimension within a conjunctive match should
ordinarily have more than one flow. Open vSwitch
does not enforce this.
Conjunction ID Field
Name: conj_id
Width: 32 bits
Format: decimal
Masking: not maskable
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CONJ_ID (37) since Open vSwitch 2.4
Used for conjunctive matching. See above for more information.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
───────────────────── ──────────────── ───── ──── ──────── ─────────────────────
tun_id aka tunnel_id 8 yes yes none OF 1.3+ and OVS 1.1+
tun_src 4 yes yes none OVS 2.0+
tun_dst 4 yes yes none OVS 2.0+
tun_ipv6_src 16 yes yes none OVS 2.5+
tun_ipv6_dst 16 yes yes none OVS 2.5+
tun_gbp_id 2 yes yes none OVS 2.4+
tun_gbp_flags 1 yes yes none OVS 2.4+
tun_erspan_ver 1 (low 4 bits) yes yes none OVS 2.10+
tun_erspan_idx 4 (low 20 bits) yes yes none OVS 2.10+
tun_erspan_dir 1 (low 1 bits) yes yes none OVS 2.10+
tun_erspan_hwid 1 (low 6 bits) yes yes none OVS 2.10+
tun_gtpu_flags 1 yes no none OVS 2.13+
tun_gtpu_msgtype 1 yes no none OVS 2.13+
tun_metadata0 124 yes yes none OVS 2.5+
tun_metadata1 124 yes yes none OVS 2.5+
tun_metadata2 124 yes yes none OVS 2.5+
tun_metadata3 124 yes yes none OVS 2.5+
tun_metadata4 124 yes yes none OVS 2.5+
tun_metadata5 124 yes yes none OVS 2.5+
tun_metadata6 124 yes yes none OVS 2.5+
tun_metadata7 124 yes yes none OVS 2.5+
tun_metadata8 124 yes yes none OVS 2.5+
tun_metadata9 124 yes yes none OVS 2.5+
tun_metadata10 124 yes yes none OVS 2.5+
tun_metadata11 124 yes yes none OVS 2.5+
tun_metadata12 124 yes yes none OVS 2.5+
tun_metadata13 124 yes yes none OVS 2.5+
tun_metadata14 124 yes yes none OVS 2.5+
tun_metadata15 124 yes yes none OVS 2.5+
tun_metadata16 124 yes yes none OVS 2.5+
tun_metadata17 124 yes yes none OVS 2.5+
tun_metadata18 124 yes yes none OVS 2.5+
tun_metadata19 124 yes yes none OVS 2.5+
tun_metadata20 124 yes yes none OVS 2.5+
tun_metadata21 124 yes yes none OVS 2.5+
tun_metadata22 124 yes yes none OVS 2.5+
tun_metadata23 124 yes yes none OVS 2.5+
tun_metadata24 124 yes yes none OVS 2.5+
tun_metadata25 124 yes yes none OVS 2.5+
tun_metadata26 124 yes yes none OVS 2.5+
tun_metadata27 124 yes yes none OVS 2.5+
tun_metadata28 124 yes yes none OVS 2.5+
tun_metadata29 124 yes yes none OVS 2.5+
tun_metadata30 124 yes yes none OVS 2.5+
tun_metadata31 124 yes yes none OVS 2.5+
tun_metadata32 124 yes yes none OVS 2.5+
tun_metadata33 124 yes yes none OVS 2.5+
tun_metadata34 124 yes yes none OVS 2.5+
tun_metadata35 124 yes yes none OVS 2.5+
tun_metadata36 124 yes yes none OVS 2.5+
tun_metadata37 124 yes yes none OVS 2.5+
tun_metadata38 124 yes yes none OVS 2.5+
tun_metadata39 124 yes yes none OVS 2.5+
tun_metadata40 124 yes yes none OVS 2.5+
tun_metadata41 124 yes yes none OVS 2.5+
tun_metadata42 124 yes yes none OVS 2.5+
tun_metadata43 124 yes yes none OVS 2.5+
tun_metadata44 124 yes yes none OVS 2.5+
tun_metadata45 124 yes yes none OVS 2.5+
tun_metadata46 124 yes yes none OVS 2.5+
tun_metadata47 124 yes yes none OVS 2.5+
tun_metadata48 124 yes yes none OVS 2.5+
tun_metadata49 124 yes yes none OVS 2.5+
tun_metadata50 124 yes yes none OVS 2.5+
tun_metadata51 124 yes yes none OVS 2.5+
tun_metadata52 124 yes yes none OVS 2.5+
tun_metadata53 124 yes yes none OVS 2.5+
tun_metadata54 124 yes yes none OVS 2.5+
tun_metadata55 124 yes yes none OVS 2.5+
tun_metadata56 124 yes yes none OVS 2.5+
tun_metadata57 124 yes yes none OVS 2.5+
tun_metadata58 124 yes yes none OVS 2.5+
tun_metadata59 124 yes yes none OVS 2.5+
tun_metadata60 124 yes yes none OVS 2.5+
tun_metadata61 124 yes yes none OVS 2.5+
tun_metadata62 124 yes yes none OVS 2.5+
tun_metadata63 124 yes yes none OVS 2.5+
tun_flags 2 (low 1 bits) yes yes none OVS 2.5+
The fields in this group relate to tunnels, which Open vSwitch
supports in several forms (GRE, VXLAN, and so on). Most of these
fields do appear in the wire format of a packet, so they are data
fields from that point of view, but they are metadata from an
OpenFlow flow table point of view because they do not appear in
packets that are forwarded to the controller or to ordinary (non-
tunnel) output ports.
Open vSwitch supports a spectrum of usage models for mapping
tunnels to OpenFlow ports:
``Port-based’’ tunnels
In this model, an OpenFlow port represents one
tunnel: it matches a particular type of tunnel
traffic between two IP endpoints, with a particular
tunnel key (if keys are in use). In this situation,
in_port suffices to distinguish one tunnel from
another, so the tunnel header fields have little
importance for OpenFlow processing. (They are still
populated and may be used if it is convenient.) The
tunnel header fields play no role in sending
packets out such an OpenFlow port, either, because
the OpenFlow port itself fully specifies the tunnel
headers.
The following Open vSwitch commands create a bridge
br-int, add port tap0 to the bridge as OpenFlow
port 1, establish a port-based GRE tunnel between
the local host and remote IP 192.168.1.1 using GRE
key 5001 as OpenFlow port 2, and arranges to
forward all traffic from tap0 to the tunnel and
vice versa:
ovs-vsctl add-br br-int
ovs-vsctl add-port br-int tap0 -- set interface tap0 ofport_request=1
ovs-vsctl add-port br-int gre0 -- \
set interface gre0 ofport_request=2 type=gre \
options:remote_ip=192.168.1.1 options:key=5001
ovs-ofctl add-flow br-int in_port=1,actions=2
ovs-ofctl add-flow br-int in_port=2,actions=1
``Flow-based’’ tunnels
In this model, one OpenFlow port represents all
possible tunnels of a given type with an endpoint
on the current host, for example, all GRE tunnels.
In this situation, in_port only indicates that
traffic was received on the particular kind of
tunnel. This is where the tunnel header fields are
most important: they allow the OpenFlow tables to
discriminate among tunnels based on their IP
endpoints or keys. Tunnel header fields also
determine the IP endpoints and keys of packets sent
out such a tunnel port.
The following Open vSwitch commands create a bridge
br-int, add port tap0 to the bridge as OpenFlow
port 1, establish a flow-based GRE tunnel port 3,
and arranges to forward all traffic from tap0 to
remote IP 192.168.1.1 over a GRE tunnel with key
5001 and vice versa:
ovs-vsctl add-br br-int
ovs-vsctl add-port br-int tap0 -- set interface tap0 ofport_request=1
ovs-vsctl add-port br-int allgre -- \
set interface allgre ofport_request=3 type=gre \
options:remote_ip=flow options:key=flow
ovs-ofctl add-flow br-int \
’in_port=1 actions=set_tunnel:5001,set_field:192.168.1.1->tun_dst,3’
ovs-ofctl add-flow br-int ’in_port=3,tun_src=192.168.1.1,tun_id=5001 actions=1’
Mixed models.
One may define both flow-based and port-based
tunnels at the same time. For example, it is valid
and possibly useful to create and configure both
gre0 and allgre tunnel ports described above.
Traffic is attributed on ingress to the most
specific matching tunnel. For example, gre0 is more
specific than allgre. Therefore, if both exist,
then gre0 will be the ingress port for any GRE
traffic received from 192.168.1.1 with key 5001.
On egress, traffic may be directed to any
appropriate tunnel port. If both gre0 and allgre
are configured as already described, then the
actions 2 and
set_tunnel:5001,set_field:192.168.1.1->tun_dst,3
send the same tunnel traffic.
Intermediate models.
Ports may be configured as partially flow-based.
For example, one may define an OpenFlow port that
represents tunnels between a pair of endpoints but
leaves the flow table to discriminate on the flow
key.
ovs-vswitchd.conf.db(5) describes all the details of tunnel
configuration.
These fields do not have any prerequisites, which means that a
flow may match on any or all of them, in any combination.
These fields are zeros for packets that did not arrive on a
tunnel.
Tunnel ID Field
Name: tun_id (aka tunnel_id)
Width: 64 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_TUNNEL_ID (38) since OpenFlow 1.3 and
Open vSwitch 1.10
NXM: NXM_NX_TUN_ID (16) since Open vSwitch 1.1
Many kinds of tunnels support a tunnel ID:
• VXLAN and Geneve have a 24-bit virtual network
identifier (VNI).
• LISP has a 24-bit instance ID.
• GRE has an optional 32-bit key.
• STT has a 64-bit key.
• ERSPAN has a 10-bit key (Session ID).
• GTPU has a 32-bit key (Tunnel Endpoint ID).
When a packet is received from a tunnel, this field holds the
tunnel ID in its least significant bits, zero-extended to fit.
This field is zero if the tunnel does not support an ID, or if no
ID is in use for a tunnel type that has an optional ID, or if an
ID of zero received, or if the packet was not received over a
tunnel.
When a packet is output to a tunnel port, the tunnel
configuration determines whether the tunnel ID is taken from this
field or bound to a fixed value. See the earlier description of
``port-based’’ and ``flow-based’’ tunnels for more information.
The following diagram shows the origin of this field in a typical
keyed GRE tunnel:
Ethernet IPv4 GRE Ethernet
<-----------> <---------------> <------------> <---------->
48 48 16 8 32 32 16 16 32 48 48 16
+---+---+-----+ +---+-----+---+---+ +---+------+---+ +---+---+----+
|dst|src|type | |...|proto|src|dst| |...| type |key| |dst|src|type| ...
+---+---+-----+ +---+-----+---+---+ +---+------+---+ +---+---+----+
0x800 47 0x6558
Tunnel IPv4 Source Field
Name: tun_src
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_IPV4_SRC (31) since Open vSwitch 2.0
When a packet is received from a tunnel, this field is the source
address in the outer IP header of the tunneled packet. This field
is zero if the packet was not received over a tunnel.
When a packet is output to a flow-based tunnel port, this field
influences the IPv4 source address used to send the packet. If it
is zero, then the kernel chooses an appropriate IP address based
using the routing table.
The following diagram shows the origin of this field in a typical
keyed GRE tunnel:
Ethernet IPv4 GRE Ethernet
<-----------> <---------------> <------------> <---------->
48 48 16 8 32 32 16 16 32 48 48 16
+---+---+-----+ +---+-----+---+---+ +---+------+---+ +---+---+----+
|dst|src|type | |...|proto|src|dst| |...| type |key| |dst|src|type| ...
+---+---+-----+ +---+-----+---+---+ +---+------+---+ +---+---+----+
0x800 47 0x6558
Tunnel IPv4 Destination Field
Name: tun_dst
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_IPV4_DST (32) since Open vSwitch 2.0
When a packet is received from a tunnel, this field is the
destination address in the outer IP header of the tunneled
packet. This field is zero if the packet was not received over a
tunnel.
When a packet is output to a flow-based tunnel port, this field
specifies the destination to which the tunnel packet is sent.
The following diagram shows the origin of this field in a typical
keyed GRE tunnel:
Ethernet IPv4 GRE Ethernet
<-----------> <---------------> <------------> <---------->
48 48 16 8 32 32 16 16 32 48 48 16
+---+---+-----+ +---+-----+---+---+ +---+------+---+ +---+---+----+
|dst|src|type | |...|proto|src|dst| |...| type |key| |dst|src|type| ...
+---+---+-----+ +---+-----+---+---+ +---+------+---+ +---+---+----+
0x800 47 0x6558
Tunnel IPv6 Source Field
Name: tun_ipv6_src
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_IPV6_SRC (109) since Open vSwitch 2.5
Similar to tun_src, but for tunnels over IPv6.
Tunnel IPv6 Destination Field
Name: tun_ipv6_dst
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_IPV6_DST (110) since Open vSwitch 2.5
Similar to tun_dst, but for tunnels over IPv6.
VXLAN Group-Based Policy Fields
The VXLAN header is defined as follows [RFC 7348], where the I
bit must be set to 1, unlabeled bits or those labeled reserved
must be set to 0, and Open vSwitch makes the VNI available via
tun_id:
VXLAN flags
<------------->
1 1 1 1 1 1 1 1 24 24 8
+-+-+-+-+-+-+-+-+--------+---+--------+
| | | | |I| | | |reserved|VNI|reserved|
+-+-+-+-+-+-+-+-+--------+---+--------+
VXLAN Group-Based Policy [VXLAN Group Policy Option] adds new
interpretations to existing bits in the VXLAN header,
reinterpreting it as follows, with changes highlighted:
GBP flags
<------------->
1 1 1 1 1 1 1 1 24 24 8
+-+-+-+-+-+-+-+-+---------------+---+--------+
| |D| | |A| | | |group policy ID|VNI|reserved|
+-+-+-+-+-+-+-+-+---------------+---+--------+
Open vSwitch makes GBP fields and flags available through the
following fields. Only packets that arrive over a VXLAN tunnel
with the GBP extension enabled have these fields set. In other
packets they are zero on receive and ignored on transmit.
VXLAN Group-Based Policy ID Field
Name: tun_gbp_id
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_GBP_ID (38) since Open vSwitch 2.4
For a packet tunneled over VXLAN with the Group-Based Policy
(GBP) extension, this field represents the GBP policy ID, as
shown above.
VXLAN Group-Based Policy Flags Field
Name: tun_gbp_flags
Width: 8 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_GBP_FLAGS (39) since Open vSwitch 2.4
For a packet tunneled over VXLAN with the Group-Based Policy
(GBP) extension, this field represents the GBP policy flags, as
shown above.
The field has the format shown below:
GBP Flags
<------------->
1 1 1 1 1 1 1 1
+-+-+-+-+-+-+-+-+
| |D| | |A| | | |
+-+-+-+-+-+-+-+-+
Unlabeled bits are reserved and must be transmitted as 0. The
VXLAN GBP draft defines the other bits’ meanings as:
D (Don’t Learn)
When set, this bit indicates that the egress tunnel
endpoint must not learn the source address of the
encapsulated frame.
A (Applied)
When set, indicates that the group policy has
already been applied to this packet. Devices must
not apply policies when the A bit is set.
ERSPAN Metadata Fields
These fields provide access to features in the ERSPAN tunneling
protocol [ERSPAN], which has two major versions: version 1 (aka
type II) and version 2 (aka type III).
Regardless of version, ERSPAN is encapsulated within a fixed
8-byte GRE header that consists of a 4-byte GRE base header and a
4-byte sequence number. The ERSPAN version 1 header format is:
GRE ERSPAN v1 Ethernet
<------------> <---------------------> <---------->
16 16 32 4 18 10 12 20 48 48 16
+---+------+---+ +---+---+-------+---+---+ +---+---+----+
|...| type |seq| |ver|...|session|...|idx| |dst|src|type| ...
+---+------+---+ +---+---+-------+---+---+ +---+---+----+
0x88be 1 tun_id
The ERSPAN version 2 header format is:
GRE ERSPAN v2 Ethernet
<------------> <----------------------------------------> <---------->
16 16 32 4 18 10 32 22 6 1 3 48 48 16
+---+------+---+ +---+---+-------+---------+---+----+---+---+ +---+---+----+
|...| type |seq| |ver|...|session|timestamp|...|hwid|dir|...| |dst|src|type| ...
+---+------+---+ +---+---+-------+---------+---+----+---+---+ +---+---+----+
0x22eb 2 tun_id 0/1
ERSPAN Version Field
Name: tun_erspan_ver
Width: 8 bits (only the least-significant 4 bits may be nonzero)
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_ET_ERSPAN_VER (12) since Open vSwitch 2.10
ERSPAN version number: 1 for version 1, or 2 for version 2.
ERSPAN Index Field
Name: tun_erspan_idx
Width: 32 bits (only the least-significant 20 bits may be nonzero)
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_ET_ERSPAN_IDX (11) since Open vSwitch 2.10
This field is a 20-bit index/port number associated with the
ERSPAN traffic’s source port and direction (ingress/egress). This
field is platform dependent.
ERSPAN Direction Field
Name: tun_erspan_dir
Width: 8 bits (only the least-significant 1 bits may be nonzero)
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_ET_ERSPAN_DIR (13) since Open vSwitch 2.10
For ERSPAN v2, the mirrored traffic’s direction: 0 for ingress
traffic, 1 for egress traffic.
ERSPAN Hardware ID Field
Name: tun_erspan_hwid
Width: 8 bits (only the least-significant 6 bits may be nonzero)
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_ET_ERSPAN_HWID (14) since Open vSwitch 2.10
A 6-bit unique identifier of an ERSPAN v2 engine within a system.
GTP-U Metadata Fields
These fields provide access to set-up GPRS Tunnelling Protocol
for User Plane (GTPv1-U), based on 3GPP TS 29.281. A GTP-U header
has the following format:
8 8 16 32
+-----+--------+------+----+
|flags|msg type|length|TEID| ...
+-----+--------+------+----+
The flags and message type have the Open vSwitch GTP-U specific
fields described below. Open vSwitch makes the TEID (Tunnel
Endpoint Identifier), which identifies a tunnel endpoint in the
receiving GTP-U protocol entity, available via tun_id.
GTP-U Flags Field
Name: tun_gtpu_flags
Width: 8 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_ET_GTPU_FLAGS (15) since Open vSwitch 2.13
This field holds the 8-bit GTP-U flags, encoded as:
GTP-U Tunnel Flags
<------------------->
3 1 1 1 1 1
+-------+--+---+-+-+--+
|version|PT|rsv|E|S|PN|
+-------+--+---+-+-+--+
1 0
The flags are:
version
Used to determine the version of the GTP-U
protocol, which should be set to 1.
PT Protocol type, used as a protocol discriminator
between GTP (1) and GTP’ (0).
rsv Reserved. Must be zero.
E If 1, indicates the presence of a meaningful value
of the Next Extension Header field.
S If 1, indicates the presence of a meaningful value
of the Sequence Number field.
PN If 1, indicates the presence of a meaningful value
of the N-PDU Number field.
GTP-U Message Type Field
Name: tun_gtpu_msgtype
Width: 8 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_ET_GTPU_MSGTYPE (16) since Open vSwitch
2.13
This field indicates whether it’s a signalling message used for
path management, or a user plane message which carries the
original packet. The complete range of message types can be
referred to [3GPP TS 29.281].
Geneve Fields
These fields provide access to additional features in the Geneve
tunneling protocol [Geneve]. Their names are somewhat generic in
the hope that the same fields could be reused for other protocols
in the future; for example, the NSH protocol [NSH] supports TLV
options whose form is identical to that for Geneve options.
Generic Tunnel Option 0 Field
Name: tun_metadata0
Width: 992 bits (124 bytes)
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_METADATA0 (40) since Open vSwitch 2.5
The above information specifically covers generic tunnel option
0, but Open vSwitch supports 64 options, numbered 0 through 63,
whose NXM field numbers are 40 through 103.
These fields provide OpenFlow access to the generic type-length-
value options defined by the Geneve tunneling protocol or other
protocols with options in the same TLV format as Geneve options.
Each of these options has the following wire format:
header body
<-------------------> <------------------>
16 8 3 5 4×(length - 1) bytes
+-----+----+---+------+--------------------+
|class|type|res|length| value |
+-----+----+---+------+--------------------+
0
Taken together, the class and type in the option format mean that
there are about 16 million distinct kinds of TLV options, too
many to give individual OXM code points. Thus, Open vSwitch
requires the user to define the TLV options of interest, by
binding up to 64 TLV options to generic tunnel option NXM code
points. Each option may have up to 124 bytes in its body, the
maximum allowed by the TLV format, but bound options may total at
most 252 bytes of body.
Open vSwitch extensions to the OpenFlow protocol bind TLV options
to NXM code points. The ovs-ofctl(8) program offers one way to
use these extensions, e.g. to configure a mapping from a TLV
option with class 0xffff, type 0, and a body length of 4 bytes:
ovs-ofctl add-tlv-map br0 "{class=0xffff,type=0,len=4}->tun_metadata0"
Once a TLV option is properly bound, it can be accessed and
modified like any other field, e.g. to send packets that have
value 1234 for the option described above to the controller:
ovs-ofctl add-flow br0 tun_metadata0=1234,actions=controller
An option not received or not bound is matched as all zeros.
Tunnel Flags Field
Name: tun_flags
Width: 16 bits (only the least-significant 1 bits may be nonzero)
Format: tunnel flags
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_TUN_FLAGS (104) since Open vSwitch 2.5
Flags indicating various aspects of the tunnel encapsulation.
Matches on this field are most conveniently written in terms of
symbolic names (given in the diagram below), each preceded by
either + for a flag that must be set, or - for a flag that must
be unset, without any other delimiters between the flags. Flags
not mentioned are wildcarded. For example, tun_flags=+oam matches
only OAM packets. Matches can also be written as flags/mask,
where flags and mask are 16-bit numbers in decimal or in
hexadecimal prefixed by 0x.
Currently, only one flag is defined:
oam The tunnel protocol indicated that this is an OAM
(Operations and Management) control packet.
The switch may reject matches against unknown flags.
Newer versions of Open vSwitch may introduce additional flags
with new meanings. It is therefore not recommended to use an
exact match on this field since the behavior of these new flags
is unknown and should be ignored.
For non-tunneled packets, the value is 0.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
────────────── ────── ───── ──── ──────── ─────────────────────
in_port 2 no yes none OVS 1.1+
in_port_oxm 4 no yes none OF 1.2+ and OVS 1.7+
skb_priority 4 no no none
pkt_mark 4 yes yes none OVS 2.0+
actset_output 4 no no none OF 1.3+ and OVS 2.4+
packet_type 4 no no none OF 1.5+ and OVS 2.8+
These fields relate to the origin or treatment of a packet, but
they are not extracted from the packet data itself.
Ingress Port Field
Name: in_port
Width: 16 bits
Format: OpenFlow 1.0 port
Masking: not maskable
Prerequisites: none
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: none
NXM: NXM_OF_IN_PORT (0) since Open vSwitch 1.1
The OpenFlow port on which the packet being processed arrived.
This is a 16-bit field that holds an OpenFlow 1.0 port number.
For receiving a packet, the only values that appear in this field
are:
1 through 0xfeff (65,279), inclusive.
Conventional OpenFlow port numbers.
OFPP_LOCAL (0xfffe or 65,534).
The ``local’’ port, which in Open vSwitch is always
named the same as the bridge itself. This
represents a connection between the switch and the
local TCP/IP stack. This port is where an IP
address is most commonly configured on an Open
vSwitch switch.
OpenFlow does not require a switch to have a local
port, but all existing versions of Open vSwitch
have always included a local port. Future
Directions: Future versions of Open vSwitch might
be able to optionally omit the local port, if
someone submits code to implement such a feature.
OFPP_NONE (OpenFlow 1.0) or OFPP_ANY (OpenFlow 1.1+)
(0xffff or 65,535).
OFPP_CONTROLLER (0xfffd or 65,533).
When a controller injects a packet into an OpenFlow
switch with a ``packet-out’’ request, it can specify
one of these ingress ports to indicate that the
packet was generated internally rather than having
been received on some port.
OpenFlow 1.0 specified OFPP_NONE for this purpose.
Despite that, some controllers used OFPP_CONTROLLER,
and some switches only accepted OFPP_CONTROLLER, so
OpenFlow 1.0.2 required support for both ports.
OpenFlow 1.1 and later were more clearly drafted to
allow only OFPP_CONTROLLER. For maximum
compatibility, Open vSwitch allows both ports with
all OpenFlow versions.
Values not mentioned above will never appear when receiving a
packet, including the following notable values:
0 Zero is not a valid OpenFlow port number.
OFPP_MAX (0xff00 or 65,280).
This value has only been clearly specified as a
valid port number as of OpenFlow 1.3.3. Before
that, its status was unclear, and so Open vSwitch
has never allowed OFPP_MAX to be used as a port
number, so packets will never be received on this
port. (Other OpenFlow switches, of course, might
use it.)
OFPP_UNSET (0xfff7 or 65,527)
OFPP_IN_PORT (0xfff8 or 65,528)
OFPP_TABLE (0xfff9 or 65,529)
OFPP_NORMAL (0xfffa or 65,530)
OFPP_FLOOD (0xfffb or 65,531)
OFPP_ALL (0xfffc or 65,532)
These port numbers are used only in output actions
and never appear as ingress ports.
Most of these port numbers were defined in OpenFlow
1.0, but OFPP_UNSET was only introduced in OpenFlow
1.5.
Values that will never appear when receiving a packet may still
be matched against in the flow table. There are still
circumstances in which those flows can be matched:
• The resubmit Open vSwitch extension action allows a
flow table lookup with an arbitrary ingress port.
• An action that modifies the ingress port field (see
below), such as e.g. load or set_field, followed by
an action or instruction that performs another flow
table lookup, such as resubmit or goto_table.
This field is heavily used for matching in OpenFlow tables, but
for packet egress, it has only very limited roles:
• OpenFlow requires suppressing output actions to
in_port. That is, the following two flows both drop
all packets that arrive on port 1:
in_port=1,actions=1
in_port=1,actions=drop
(This behavior is occasionally useful for flooding
to a subset of ports. Specifying actions=1,2,3,4,
for example, outputs to ports 1, 2, 3, and 4,
omitting the ingress port.)
• OpenFlow has a special port OFPP_IN_PORT (with
value 0xfff8) that outputs to the ingress port. For
example, in a switch that has four ports numbered 1
through 4, actions=1,2,3,4,in_port outputs to ports
1, 2, 3, and 4, including the ingress port.
Because the ingress port field has so little influence on packet
processing, it does not ordinarily make sense to modify the
ingress port field. The field is writable only to support the
occasional use case where the ingress port’s roles in packet
egress, described above, become troublesome. For example,
actions=load:0->NXM_OF_IN_PORT[],output:123 will output to port
123 regardless of whether it is in the ingress port. If the
ingress port is important, then one may save and restore it on
the stack:
actions=push:NXM_OF_IN_PORT[],load:0->NXM_OF_IN_PORT[],output:123,pop:NXM_OF_IN_PORT[]
or, in Open vSwitch 2.7 or later, use the clone action to save
and restore it:
actions=clone(load:0->NXM_OF_IN_PORT[],output:123)
The ability to modify the ingress port is an Open vSwitch
extension to OpenFlow.
OXM Ingress Port Field
Name: in_port_oxm
Width: 32 bits
Format: OpenFlow 1.1+ port
Masking: not maskable
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_IN_PORT (0) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: none
OpenFlow 1.1 and later use a 32-bit port number, so this field
supplies a 32-bit view of the ingress port. Current versions of
Open vSwitch support only a 16-bit range of ports:
• OpenFlow 1.0 ports 0x0000 to 0xfeff, inclusive, map
to OpenFlow 1.1 port numbers with the same values.
• OpenFlow 1.0 ports 0xff00 to 0xffff, inclusive, map
to OpenFlow 1.1 port numbers 0xffffff00 to
0xffffffff.
• OpenFlow 1.1 ports 0x0000ff00 to 0xfffffeff are not
mapped and not supported.
in_port and in_port_oxm are two views of the same information, so
all of the comments on in_port apply to in_port_oxm too.
Modifying in_port changes in_port_oxm, and vice versa.
Setting in_port_oxm to an unsupported value yields unspecified
behavior.
Output Queue Field
Name: skb_priority
Width: 32 bits
Format: hexadecimal
Masking: not maskable
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: none
Future Directions: Open vSwitch implements the output queue as a
field, but does not currently expose it through OXM or NXM for
matching purposes. If this turns out to be a useful feature, it
could be implemented in future versions. Only the set_queue,
enqueue, and pop_queue actions currently influence the output
queue.
This field influences how packets in the flow will be queued, for
quality of service (QoS) purposes, when they egress the switch.
Its range of meaningful values, and their meanings, varies
greatly from one OpenFlow implementation to another. Even within
a single implementation, there is no guarantee that all OpenFlow
ports have the same queues configured or that all OpenFlow ports
in an implementation can be configured the same way queue-wise.
Configuring queues on OpenFlow is not well standardized. On
Linux, Open vSwitch supports queue configuration via OVSDB,
specifically the QoS and Queue tables (see
ovs-vswitchd.conf.db(5) for details). Ports of Open vSwitch to
other platforms might require queue configuration through some
separate protocol (such as a CLI). Even on Linux, Open vSwitch
exposes only a fraction of the kernel’s queuing features through
OVSDB, so advanced or unusual uses might require use of separate
utilities (e.g. tc). OpenFlow switches other than Open vSwitch
might use OF-CONFIG or any of the configuration methods mentioned
above. Finally, some OpenFlow switches have a fixed number of
fixed-function queues (e.g. eight queues with strictly defined
priorities) and others do not support any control over queuing.
The only output queue that all OpenFlow implementations must
support is zero, to identify a default queue, whose properties
are implementation-defined. Outputting a packet to a queue that
does not exist on the output port yields unpredictable behavior:
among the possibilities are that the packet might be dropped or
transmitted with a very high or very low priority.
OpenFlow 1.0 only allowed output queues to be specified as part
of an enqueue action that specified both a queue and an output
port. That is, OpenFlow 1.0 treats the queue as an argument to an
action, not as a field.
To increase flexibility, OpenFlow 1.1 added an action to set the
output queue. This model was carried forward, without change,
through OpenFlow 1.5.
Open vSwitch implements the native queuing model of each OpenFlow
version it supports. Open vSwitch also includes an extension for
setting the output queue as an action in OpenFlow 1.0.
When a packet ingresses into an OpenFlow switch, the output queue
is ordinarily set to 0, indicating the default queue. However,
Open vSwitch supports various ways to forward a packet from one
OpenFlow switch to another within a single host. In these cases,
Open vSwitch maintains the output queue across the forwarding
step. For example:
• A hop across an Open vSwitch ``patch port’’ (which
does not actually involve queuing) preserves the
output queue.
• When a flow sets the output queue then outputs to
an OpenFlow tunnel port, the encapsulation
preserves the output queue. If the kernel TCP/IP
stack routes the encapsulated packet directly to a
physical interface, then that output honors the
output queue. Alternatively, if the kernel routes
the encapsulated packet to another Open vSwitch
bridge, then the output queue set previously
becomes the initial output queue on ingress to the
second bridge and will thus be used for further
output actions (unless overridden by a new ``set
queue’’ action).
(This description reflects the current behavior of
Open vSwitch on Linux. This behavior relies on
details of the Linux TCP/IP stack. It could be
difficult to make ports to other operating systems
behave the same way.)
Packet Mark Field
Name: pkt_mark
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_PKT_MARK (33) since Open vSwitch 2.0
Packet mark comes to Open vSwitch from the Linux kernel, in which
the sk_buff data structure that represents a packet contains a
32-bit member named skb_mark. The value of skb_mark propagates
along with the packet it accompanies wherever the packet goes in
the kernel. It has no predefined semantics but various kernel-
user interfaces can set and match on it, which makes it suitable
for ``marking’’ packets at one point in their handling and then
acting on the mark later. With iptables, for example, one can
mark some traffic specially at ingress and then handle that
traffic differently at egress based on the marked value.
Packet mark is an attempt at a generalization of the skb_mark
concept beyond Linux, at least through more generic naming. Like
skb_priority, packet mark is preserved across forwarding steps
within a machine. Unlike skb_priority, packet mark has no direct
effect on packet forwarding: the value set in packet mark does
not matter unless some later OpenFlow table or switch matches on
packet mark, or unless the packet passes through some other
kernel subsystem that has been configured to interpret packet
mark in specific ways, e.g. through iptables configuration
mentioned above.
Preserving packet mark across kernel forwarding steps relies
heavily on kernel support, which ports to non-Linux operating
systems may not have. Regardless of operating system support,
Open vSwitch supports packet mark within a single bridge and
across patch ports.
The value of packet mark when a packet ingresses into the first
Open vSwich bridge is typically zero, but it could be nonzero if
its value was previously set by some kernel subsystem.
Action Set Output Port Field
Name: actset_output
Width: 32 bits
Format: OpenFlow 1.1+ port
Masking: not maskable
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: ONFOXM_ET_ACTSET_OUTPUT (43) since OpenFlow 1.3
and Open vSwitch 2.4; OXM_OF_ACTSET_OUTPUT (43)
since OpenFlow 1.5 and Open vSwitch 2.4
NXM: none
Holds the output port currently in the OpenFlow action set (i.e.
from an output action within a write_actions instruction). Its
value is an OpenFlow port number. If there is no output port in
the OpenFlow action set, or if the output port will be ignored
(e.g. because there is an output group in the OpenFlow action
set), then the value will be OFPP_UNSET.
Open vSwitch allows any table to match this field. OpenFlow,
however, only requires this field to be matchable from within an
OpenFlow egress table (a feature that Open vSwitch does not yet
implement).
Packet Type Field
Name: packet_type
Width: 32 bits
Format: packet type
Masking: not maskable
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_PACKET_TYPE (44) since OpenFlow 1.5 and
Open vSwitch 2.8
NXM: none
The type of the packet in the format specified in OpenFlow 1.5:
Packet type
<--------->
16 16
+---+-------+
|ns |ns_type| ...
+---+-------+
The upper 16 bits, ns, are a namespace. The meaning of ns_type
depends on the namespace. The packet type field is specified and
displayed in the format (ns,ns_type).
Open vSwitch currently supports the following classes of packet
types for matching:
(0,0) Ethernet.
(1,ethertype)
The specified ethertype. Open vSwitch can forward
packets with any ethertype, but it can only match
on and process data fields for the following
supported packet types:
(1,0x800)
IPv4
(1,0x806)
ARP
(1,0x86dd)
IPv6
(1,0x8847)
MPLS
(1,0x8848)
MPLS multicast
(1,0x8035)
RARP
(1,0x894f)
NSH
Consider the distinction between a packet with packet_type=(0,0),
dl_type=0x800 and one with packet_type=(1,0x800). The former is
an Ethernet frame that contains an IPv4 packet, like this:
Ethernet IPv4
<-----------> <--------------->
48 48 16 8 32 32
+---+---+-----+ +---+-----+---+---+
|dst|src|type | |...|proto|src|dst| ...
+---+---+-----+ +---+-----+---+---+
0x800
The latter is an IPv4 packet not encapsulated inside any outer
frame, like this:
IPv4
<--------------->
8 32 32
+---+-----+---+---+
|...|proto|src|dst| ...
+---+-----+---+---+
Matching on packet_type is a pre-requisite for matching on any
data field, but for backward compatibility, when a match on a
data field is present without a packet_type match, Open vSwitch
acts as though a match on (0,0) (Ethernet) had been supplied.
Similarly, when Open vSwitch sends flow match information to a
controller, e.g. in a reply to a request to dump the flow table,
Open vSwitch omits a match on packet type (0,0) if it would be
implied by a data field match.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
──────────── ────── ───── ──── ──────── ────────────────
ct_state 4 yes no none OVS 2.5+
ct_zone 2 no no none OVS 2.5+
ct_mark 4 yes yes none OVS 2.5+
ct_label 16 yes yes none OVS 2.5+
ct_nw_src 4 yes no CT OVS 2.8+
ct_nw_dst 4 yes no CT OVS 2.8+
ct_ipv6_src 16 yes no CT OVS 2.8+
ct_ipv6_dst 16 yes no CT OVS 2.8+
ct_nw_proto 1 no no CT OVS 2.8+
ct_tp_src 2 yes no CT OVS 2.8+
ct_tp_dst 2 yes no CT OVS 2.8+
Open vSwitch supports ``connection tracking,’’ which allows
bidirectional streams of packets to be statefully grouped into
connections. Open vSwitch connection tracking, for example,
identifies the patterns of TCP packets that indicates a
successfully initiated connection, as well as those that indicate
that a connection has been torn down. Open vSwitch connection
tracking can also identify related connections, such as FTP data
connections spawned from FTP control connections.
An individual packet passing through the pipeline may be in one
of two states, ``untracked’’ or ``tracked,’’ which may be
distinguished via the ``trk’’ flag in ct_state. A packet is
untracked at the beginning of the Open vSwitch pipeline and
continues to be untracked until the pipeline invokes the ct
action. The connection tracking fields are all zeroes in an
untracked packet. When a flow in the Open vSwitch pipeline
invokes the ct action, the action initializes the connection
tracking fields and the packet becomes tracked for the remainder
of its processing.
The connection tracker stores connection state in an internal
table, but it only adds a new entry to this table when a ct
action for a new connection invokes ct with the commit parameter.
For a given connection, when a pipeline has executed ct, but not
yet with commit, the connection is said to be uncommitted. State
for an uncommitted connection is ephemeral and does not persist
past the end of the pipeline, so some features are only available
to committed connections. A connection would typically be left
uncommitted as a way to drop its packets.
Connection tracking is an Open vSwitch extension to OpenFlow.
Open vSwitch 2.5 added the initial support for connection
tracking. Subsequent versions of Open vSwitch added many
refinements and extensions to the initial support. Many of these
capabilities depend on the Open vSwitch datapath rather than
simply the userspace version. The capabilities column in the
Datapath table (see ovs-vswitchd.conf.db(5)) reports the detailed
capabilities of a particular Open vSwitch datapath.
Connection Tracking State Field
Name: ct_state
Width: 32 bits
Format: ct state
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_STATE (105) since Open vSwitch 2.5
This field holds several flags that can be used to determine the
state of the connection to which the packet belongs.
Matches on this field are most conveniently written in terms of
symbolic names (listed below), each preceded by either + for a
flag that must be set, or - for a flag that must be unset,
without any other delimiters between the flags. Flags not
mentioned are wildcarded. For example, tcp,ct_state=+trk-new
matches TCP packets that have been run through the connection
tracker and do not establish a new connection. Matches can also
be written as flags/mask, where flags and mask are 32-bit numbers
in decimal or in hexadecimal prefixed by 0x.
The following flags are defined:
new (0x01)
A new connection. Set to 1 if this is an
uncommitted connection.
est (0x02)
Part of an existing connection. Set to 1 if packets
of a committed connection have been seen by
conntrack from both directions.
rel (0x04)
Related to an existing connection, e.g. an ICMP
``destination unreachable’’ message or an FTP data
connections. This flag will only be 1 if the
connection to which this one is related is
committed.
Connections identified as rel are separate from the
originating connection and must be committed
separately. All packets for a related connection
will have the rel flag set, not just the initial
packet.
rpl (0x08)
This packet is in the reply direction, meaning that
it is in the opposite direction from the packet
that initiated the connection. This flag will only
be 1 if the connection is committed.
inv (0x10)
The state is invalid, meaning that the connection
tracker couldn’t identify the connection. This flag
is a catch-all for problems in the connection or
the connection tracker, such as:
• L3/L4 protocol handler is not
loaded/unavailable. With the Linux kernel
datapath, this may mean that the
nf_conntrack_ipv4 or nf_conntrack_ipv6
modules are not loaded.
• L3/L4 protocol handler determines that the
packet is malformed.
• Packets are unexpected length for protocol.
trk (0x20)
This packet is tracked, meaning that it has
previously traversed the connection tracker. If
this flag is not set, then no other flags will be
set. If this flag is set, then the packet is
tracked and other flags may also be set.
snat (0x40)
This packet was transformed by source address/port
translation by a preceding ct action. Open vSwitch
2.6 added this flag.
dnat (0x80)
This packet was transformed by destination
address/port translation by a preceding ct action.
Open vSwitch 2.6 added this flag.
There are additional constraints on these flags, listed in
decreasing order of precedence below:
1. If trk is unset, no other flags are set.
2. If trk is set, one or more other flags may be set.
3. If inv is set, only the trk flag is also set.
4. new and est are mutually exclusive.
5. new and rpl are mutually exclusive.
6. rel may be set in conjunction with any other flags.
Future versions of Open vSwitch may define new flags.
Connection Tracking Zone Field
Name: ct_zone
Width: 16 bits
Format: hexadecimal
Masking: not maskable
Prerequisites: none
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_ZONE (106) since Open vSwitch 2.5
A connection tracking zone, the zone value passed to the most
recent ct action. Each zone is an independent connection tracking
context, so tracking the same packet in multiple contexts
requires using the ct action multiple times.
Connection Tracking Mark Field
Name: ct_mark
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_MARK (107) since Open vSwitch 2.5
The metadata committed, by an action within the exec parameter to
the ct action, to the connection to which the current packet
belongs.
Connection Tracking Label Field
Name: ct_label
Width: 128 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_LABEL (108) since Open vSwitch 2.5
The label committed, by an action within the exec parameter to
the ct action, to the connection to which the current packet
belongs.
Open vSwitch 2.8 introduced the matching support for connection
tracker original direction 5-tuple fields.
For non-committed non-related connections the conntrack original
direction tuple fields always have the same values as the
corresponding headers in the packet itself. For any other packets
of a committed connection the conntrack original direction tuple
fields reflect the values from that initial non-committed non-
related packet, and thus may be different from the actual packet
headers, as the actual packet headers may be in reverse direction
(for reply packets), transformed by NAT (when nat option was
applied to the connection), or be of different protocol (i.e.,
when an ICMP response is sent to an UDP packet). In case of
related connections, e.g., an FTP data connection, the original
direction tuple contains the original direction headers from the
parent connection, e.g., an FTP control connection.
The following fields are populated by the ct action, and require
a match to a valid connection tracking state as a prerequisite,
in addition to the IP or IPv6 ethertype match. Examples of valid
connection tracking state matches include ct_state=+new,
ct_state=+est, ct_state=+rel, and ct_state=+trk-inv.
Connection Tracking Original Direction IPv4 Source Address Field
Name: ct_nw_src
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_NW_SRC (120) since Open vSwitch 2.8
Matches IPv4 conntrack original direction tuple source address.
See the paragraphs above for general description to the conntrack
original direction tuple. Introduced in Open vSwitch 2.8.
Connection Tracking Original Direction IPv4 Destination Address
Field
Name: ct_nw_dst
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_NW_DST (121) since Open vSwitch 2.8
Matches IPv4 conntrack original direction tuple destination
address. See the paragraphs above for general description to the
conntrack original direction tuple. Introduced in Open vSwitch
2.8.
Connection Tracking Original Direction IPv6 Source Address Field
Name: ct_ipv6_src
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_IPV6_SRC (122) since Open vSwitch 2.8
Matches IPv6 conntrack original direction tuple source address.
See the paragraphs above for general description to the conntrack
original direction tuple. Introduced in Open vSwitch 2.8.
Connection Tracking Original Direction IPv6 Destination Address
Field
Name: ct_ipv6_dst
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_IPV6_DST (123) since Open vSwitch 2.8
Matches IPv6 conntrack original direction tuple destination
address. See the paragraphs above for general description to the
conntrack original direction tuple. Introduced in Open vSwitch
2.8.
Connection Tracking Original Direction IP Protocol Field
Name: ct_nw_proto
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_NW_PROTO (119) since Open vSwitch 2.8
Matches conntrack original direction tuple IP protocol type,
which is specified as a decimal number between 0 and 255,
inclusive (e.g. 1 to match ICMP packets or 6 to match TCP
packets). In case of, for example, an ICMP response to an UDP
packet, this may be different from the IP protocol type of the
packet itself. See the paragraphs above for general description
to the conntrack original direction tuple. Introduced in Open
vSwitch 2.8.
Connection Tracking Original Direction Transport Layer Source
Port Field
Name: ct_tp_src
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_TP_SRC (124) since Open vSwitch 2.8
Bitwise match on the conntrack original direction tuple transport
source, when MFF_CT_NW_PROTO has value 6 for TCP, 17 for UDP, or
132 for SCTP. When MFF_CT_NW_PROTO has value 1 for ICMP, or 58
for ICMPv6, the lower 8 bits of MFF_CT_TP_SRC matches the
conntrack original direction ICMP type. See the paragraphs above
for general description to the conntrack original direction
tuple. Introduced in Open vSwitch 2.8.
Connection Tracking Original Direction Transport Layer Source
Port Field
Name: ct_tp_dst
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: CT
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_CT_TP_DST (125) since Open vSwitch 2.8
Bitwise match on the conntrack original direction tuple transport
destination port, when MFF_CT_NW_PROTO has value 6 for TCP, 17
for UDP, or 132 for SCTP. When MFF_CT_NW_PROTO has value 1 for
ICMP, or 58 for ICMPv6, the lower 8 bits of MFF_CT_TP_DST matches
the conntrack original direction ICMP code. See the paragraphs
above for general description to the conntrack original direction
tuple. Introduced in Open vSwitch 2.8.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
───────── ────── ───── ──── ──────── ─────────────────────
metadata 8 yes yes none OF 1.2+ and OVS 1.8+
reg0 4 yes yes none OVS 1.1+
reg1 4 yes yes none OVS 1.1+
reg2 4 yes yes none OVS 1.1+
reg3 4 yes yes none OVS 1.1+
reg4 4 yes yes none OVS 1.3+
reg5 4 yes yes none OVS 1.7+
reg6 4 yes yes none OVS 1.7+
reg7 4 yes yes none OVS 1.7+
reg8 4 yes yes none OVS 2.6+
reg9 4 yes yes none OVS 2.6+
reg10 4 yes yes none OVS 2.6+
reg11 4 yes yes none OVS 2.6+
reg12 4 yes yes none OVS 2.6+
reg13 4 yes yes none OVS 2.6+
reg14 4 yes yes none OVS 2.6+
reg15 4 yes yes none OVS 2.6+
xreg0 8 yes yes none OF 1.3+ and OVS 2.4+
xreg1 8 yes yes none OF 1.3+ and OVS 2.4+
xreg2 8 yes yes none OF 1.3+ and OVS 2.4+
xreg3 8 yes yes none OF 1.3+ and OVS 2.4+
xreg4 8 yes yes none OF 1.3+ and OVS 2.4+
xreg5 8 yes yes none OF 1.3+ and OVS 2.4+
xreg6 8 yes yes none OF 1.3+ and OVS 2.4+
xreg7 8 yes yes none OF 1.3+ and OVS 2.4+
xxreg0 16 yes yes none OVS 2.6+
xxreg1 16 yes yes none OVS 2.6+
xxreg2 16 yes yes none OVS 2.6+
xxreg3 16 yes yes none OVS 2.6+
These fields give an OpenFlow switch space for temporary storage
while the pipeline is running. Whereas metadata fields can have a
meaningful initial value and can persist across some hops across
OpenFlow switches, registers are always initially 0 and their
values never persist across inter-switch hops (not even across
patch ports).
OpenFlow Metadata Field
Name: metadata
Width: 64 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes
OXM: OXM_OF_METADATA (2) since OpenFlow 1.2 and Open
vSwitch 1.8
NXM: none
This field is the oldest standardized OpenFlow register field,
introduced in OpenFlow 1.1. It was introduced to model the
limited number of user-defined bits that some ASIC-based switches
can carry through their pipelines. Because of hardware
limitations, OpenFlow allows switches to support writing and
masking only an implementation-defined subset of bits, even no
bits at all. The Open vSwitch software switch always supports all
64 bits, but of course an Open vSwitch port to an ASIC would have
the same restriction as the ASIC itself.
This field has an OXM code point, but OpenFlow 1.4 and earlier
allow it to be modified only with a specialized instruction, not
with a ``set-field’’ action. OpenFlow 1.5 removes this
restriction. Open vSwitch does not enforce this restriction,
regardless of OpenFlow version.
Register 0 Field
Name: reg0
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_REG0 (0) since Open vSwitch 1.1
This is the first of several Open vSwitch registers, all of which
have the same properties. Open vSwitch 1.1 introduced registers
0, 1, 2, and 3, version 1.3 added register 4, version 1.7 added
registers 5, 6, and 7, and version 2.6 added registers 8 through
15.
Extended Register 0 Field
Name: xreg0
Width: 64 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_PKT_REG0 (0) since OpenFlow 1.3 and Open
vSwitch 2.4
NXM: none
This is the first of the registers introduced in OpenFlow 1.5.
OpenFlow 1.5 calls these fields just the ``packet registers,’’
but Open vSwitch already had 32-bit registers by that name, so
Open vSwitch uses the name ``extended registers’’ in an attempt
to reduce confusion. The standard allows for up to 128 registers,
each 64 bits wide, but Open vSwitch only implements 4 (in
versions 2.4 and 2.5) or 8 (in version 2.6 and later).
Each of the 64-bit extended registers overlays two of the 32-bit
registers: xreg0 overlays reg0 and reg1, with reg0 supplying the
most-significant bits of xreg0 and reg1 the least-significant.
Similarly, xreg1 overlays reg2 and reg3, and so on.
The OpenFlow specification says, ``In most cases, the packet
registers can not be matched in tables, i.e. they usually can not
be used in the flow entry match structure’’ [OpenFlow 1.5,
section 7.2.3.10], but there is no reason for a software switch
to impose such a restriction, and Open vSwitch does not.
Double-Extended Register 0 Field
Name: xxreg0
Width: 128 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: none
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_XXREG0 (111) since Open vSwitch 2.6
This is the first of the double-extended registers introduce in
Open vSwitch 2.6. Each of the 128-bit extended registers overlays
four of the 32-bit registers: xxreg0 overlays reg0 through reg3,
with reg0 supplying the most-significant bits of xxreg0 and reg3
the least-significant. xxreg1 similarly overlays reg4 through
reg7, and so on.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
───────────────────── ────── ───── ──── ───────── ─────────────────────
eth_src aka dl_src 6 yes yes Ethernet OF 1.2+ and OVS 1.1+
eth_dst aka dl_dst 6 yes yes Ethernet OF 1.2+ and OVS 1.1+
eth_type aka dl_type 2 no no Ethernet OF 1.2+ and OVS 1.1+
Ethernet is the only layer-2 protocol that Open vSwitch supports.
As with most software, Open vSwitch and OpenFlow regard an
Ethernet frame to begin with the 14-byte header and end with the
final byte of the payload; that is, the frame check sequence is
not considered part of the frame.
Ethernet Source Field
Name: eth_src (aka dl_src)
Width: 48 bits
Format: Ethernet
Masking: arbitrary bitwise masks
Prerequisites: Ethernet
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes
OXM: OXM_OF_ETH_SRC (4) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_ETH_SRC (2) since Open vSwitch 1.1
The Ethernet source address:
Ethernet
<---------->
48 48 16
+---+---+----+
|dst|src|type| ...
+---+---+----+
Ethernet Destination Field
Name: eth_dst (aka dl_dst)
Width: 48 bits
Format: Ethernet
Masking: arbitrary bitwise masks
Prerequisites: Ethernet
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes
OXM: OXM_OF_ETH_DST (3) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_ETH_DST (1) since Open vSwitch 1.1
The Ethernet destination address:
Ethernet
<---------->
48 48 16
+---+---+----+
|dst|src|type| ...
+---+---+----+
Open vSwitch 1.8 and later support arbitrary masks for source
and/or destination. Earlier versions only support masking the
destination with the following masks:
01:00:00:00:00:00
Match only the multicast bit. Thus,
dl_dst=01:00:00:00:00:00/01:00:00:00:00:00 matches
all multicast (including broadcast) Ethernet
packets, and
dl_dst=00:00:00:00:00:00/01:00:00:00:00:00 matches
all unicast Ethernet packets.
fe:ff:ff:ff:ff:ff
Match all bits except the multicast bit. This is
probably not useful.
ff:ff:ff:ff:ff:ff
Exact match (equivalent to omitting the mask).
00:00:00:00:00:00
Wildcard all bits (equivalent to dl_dst=*).
Ethernet Type Field
Name: eth_type (aka dl_type)
Width: 16 bits
Format: hexadecimal
Masking: not maskable
Prerequisites: Ethernet
Access: read-only
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_ETH_TYPE (5) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_ETH_TYPE (3) since Open vSwitch 1.1
The most commonly seen Ethernet frames today use a format called
``Ethernet II,’’ in which the last two bytes of the Ethernet
header specify the Ethertype. For such a frame, this field is
copied from those bytes of the header, like so:
Ethernet
<---------------->
48 48 16
+---+---+----------+
|dst|src| type | ...
+---+---+----------+
≥0x600
Every Ethernet type has a value 0x600 (1,536) or greater. When
the last two bytes of the Ethernet header have a value too small
to be an Ethernet type, then the value found there is the total
length of the frame in bytes, excluding the Ethernet header. An
802.2 LLC header typically follows the Ethernet header. OpenFlow
and Open vSwitch only support LLC headers with DSAP and SSAP 0xaa
and control byte 0x03, which indicate that a SNAP header follows
the LLC header. In turn, OpenFlow and Open vSwitch only support a
SNAP header with organization 0x000000. In such a case, this
field is copied from the type field in the SNAP header, like
this:
Ethernet LLC SNAP
<------------> <------------> <----------------->
48 48 16 8 8 8 24 16
+---+---+------+ +----+----+----+ +--------+----------+
|dst|src| type | |DSAP|SSAP|cntl| | org | type | ...
+---+---+------+ +----+----+----+ +--------+----------+
<0x600 0xaa 0xaa 0x03 0x000000 ≥0x600
When an 802.1Q header is inserted after the Ethernet source and
destination, this field is populated with the encapsulated
Ethertype, not the 802.1Q Ethertype. With an Ethernet II inner
frame, the result looks like this:
Ethernet 802.1Q Ethertype
<------> <--------> <-------->
48 48 16 16 16
+----+---+ +------+---+ +----------+
|dst |src| | TPID |TCI| | type | ...
+----+---+ +------+---+ +----------+
0x8100 ≥0x600
LLC and SNAP encapsulation look like this with an 802.1Q header:
Ethernet 802.1Q Ethertype LLC SNAP
<------> <--------> <-------> <------------> <----------------->
48 48 16 16 16 8 8 8 24 16
+----+---+ +------+---+ +---------+ +----+----+----+ +--------+----------+
|dst |src| | TPID |TCI| | type | |DSAP|SSAP|cntl| | org | type | ...
+----+---+ +------+---+ +---------+ +----+----+----+ +--------+----------+
0x8100 <0x600 0xaa 0xaa 0x03 0x000000 ≥0x600
When a packet doesn’t match any of the header formats described
above, Open vSwitch and OpenFlow set this field to 0x5ff
(OFP_DL_TYPE_NOT_ETH_TYPE).
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
──────────── ──────────────── ───── ──── ───────── ─────────────────────
dl_vlan 2 (low 12 bits) no yes Ethernet
dl_vlan_pcp 1 (low 3 bits) no yes Ethernet
vlan_vid 2 (low 12 bits) yes yes Ethernet OF 1.2+ and OVS 1.7+
vlan_pcp 1 (low 3 bits) no yes VLAN VID OF 1.2+ and OVS 1.7+
vlan_tci 2 yes yes Ethernet OVS 1.1+
The 802.1Q VLAN header causes more trouble than any other 4 bytes
in networking. OpenFlow 1.0, 1.1, and 1.2+ all treat VLANs
differently. Open vSwitch extensions add another variant to the
mix. Open vSwitch reconciles all four treatments as best it can.
VLAN Header Format
An 802.1Q VLAN header consists of two 16-bit fields:
TPID TCI
<-------> <--------->
16 3 1 12
+---------+---+---+---+
|Ethertype|PCP|CFI|VID|
+---------+---+---+---+
0x8100 0
The first 16 bits of the VLAN header, the TPID (Tag Protocol
IDentifier), is an Ethertype. When the VLAN header is inserted
just after the source and destination MAC addresses in a
Ethertype frame, the TPID serves to identify the presence of the
VLAN. The standard TPID, the only one that Open vSwitch supports,
is 0x8100. OpenFlow 1.0 explicitly supports only TPID 0x8100.
OpenFlow 1.1, but not earlier or later versions, also requires
support for TPID 0x88a8 (Open vSwitch does not support this).
OpenFlow 1.2 through 1.5 do not require support for specific
TPIDs (the ``push vlan header’’ action does say that only 0x8100
and 0x88a8 should be pushed). No version of OpenFlow provides a
way to distinguish or match on the TPID.
The remaining 16 bits of the VLAN header, the TCI (Tag Control
Information), is subdivided into three subfields:
• PCP (Priority Control Point), is a 3-bit 802.1p
priority. The lowest priority is value 1, the
second-lowest is value 0, and priority increases
from 2 up to highest priority 7.
• CFI (Canonical Format Indicator), is a 1-bit field.
On an Ethernet network, its value is always 0. This
led to it later being repurposed under the name DEI
(Drop Eligibility Indicator). By either name,
OpenFlow and Open vSwitch don’t provide any way to
match or set this bit.
• VID (VLAN IDentifier), is a 12-bit VLAN. If the VID
is 0, then the frame is not part of a VLAN. In that
case, the VLAN header is called a priority tag
because it is only meaningful for assigning the
frame a priority. VID 0xfff (4,095) is reserved.
See eth_type for illustrations of a complete Ethernet frame with
802.1Q tag included.
Multiple VLANs
Open vSwitch can match only a single VLAN header. If more than
one VLAN header is present, then eth_type holds the TPID of the
inner VLAN header. Open vSwitch stops parsing the packet after
the inner TPID, so matching further into the packet (e.g. on the
inner TCI or L3 fields) is not possible.
OpenFlow only directly supports matching a single VLAN header. In
OpenFlow 1.1 or later, one OpenFlow table can match on the
outermost VLAN header and pop it off, and a later OpenFlow table
can match on the next outermost header. Open vSwitch does not
support this.
VLAN Field Details
The four variants have three different levels of expressiveness:
OpenFlow 1.0 and 1.1 VLAN matching are less powerful than
OpenFlow 1.2+ VLAN matching, which is less powerful than Open
vSwitch extension VLAN matching.
OpenFlow 1.0 VLAN Fields
OpenFlow 1.0 uses two fields, called dl_vlan and dl_vlan_pcp,
each of which can be either exact-matched or wildcarded, to
specify VLAN matches:
• When both dl_vlan and dl_vlan_pcp are wildcarded,
the flow matches packets without an 802.1Q header
or with any 802.1Q header.
• The match dl_vlan=0xffff causes a flow to match
only packets without an 802.1Q header. Such a flow
should also wildcard dl_vlan_pcp, since a packet
without an 802.1Q header does not have a PCP.
OpenFlow does not specify what to do if a match on
PCP is actually present, but Open vSwitch ignores
it.
• Otherwise, the flow matches only packets with an
802.1Q header. If dl_vlan is not wildcarded, then
the flow only matches packets with the VLAN ID
specified in dl_vlan’s low 12 bits. If dl_vlan_pcp
is not wildcarded, then the flow only matches
packets with the priority specified in
dl_vlan_pcp’s low 3 bits.
OpenFlow does not specify how to interpret the high
4 bits of dl_vlan or the high 5 bits of
dl_vlan_pcp. Open vSwitch ignores them.
OpenFlow 1.1 VLAN Fields
VLAN matching in OpenFlow 1.1 is similar to OpenFlow 1.0. The one
refinement is that when dl_vlan matches on 0xfffe (OFVPID_ANY),
the flow matches only packets with an 802.1Q header, with any
VLAN ID. If dl_vlan_pcp is wildcarded, the flow matches any
packet with an 802.1Q header, regardless of VLAN ID or priority.
If dl_vlan_pcp is not wildcarded, then the flow only matches
packets with the priority specified in dl_vlan_pcp’s low 3 bits.
OpenFlow 1.1 uses the name OFPVID_NONE, instead of OFP_VLAN_NONE,
for a dl_vlan of 0xffff, but it has the same meaning.
In OpenFlow 1.1, Open vSwitch reports error OFPBMC_BAD_VALUE for
an attempt to match on dl_vlan between 4,096 and 0xfffd,
inclusive, or dl_vlan_pcp greater than 7.
OpenFlow 1.2 VLAN Fields
OpenFlow 1.2+ VLAN ID Field
Name: vlan_vid
Width: 16 bits (only the least-significant 12 bits may be nonzero)
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: Ethernet
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_VLAN_VID (6) since OpenFlow 1.2 and Open vSwitch 1.7
NXM: none
The OpenFlow standard describes this field as consisting of
``12+1’’ bits. On ingress, its value is 0 if no 802.1Q header is
present, and otherwise it holds the VLAN VID in its least
significant 12 bits, with bit 12 (0x1000 aka OFPVID_PRESENT) also
set to 1. The three most significant bits are always zero:
OXM_OF_VLAN_VID
<------------->
3 1 12
+---+--+--------+
| |P |VLAN ID |
+---+--+--------+
0
As a consequence of this field’s format, one may use it to match
the VLAN ID in all of the ways available with the OpenFlow 1.0
and 1.1 formats, and a few new ways:
Fully wildcarded
Matches any packet, that is, one without an 802.1Q
header or with an 802.1Q header with any TCI value.
Value 0x0000 (OFPVID_NONE), mask 0xffff (or no mask)
Matches only packets without an 802.1Q header.
Value 0x1000, mask 0x1000
Matches any packet with an 802.1Q header,
regardless of VLAN ID.
Value 0x1009, mask 0xffff (or no mask)
Match only packets with an 802.1Q header with VLAN
ID 9.
Value 0x1001, mask 0x1001
Matches only packets that have an 802.1Q header
with an odd-numbered VLAN ID. (This is just an
example; one can match on any desired VLAN ID bit
pattern.)
OpenFlow 1.2+ VLAN Priority Field
Name: vlan_pcp
Width: 8 bits (only the least-significant 3 bits may be nonzero)
Format: decimal
Masking: not maskable
Prerequisites: VLAN VID
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_VLAN_PCP (7) since OpenFlow 1.2 and Open vSwitch
1.7
NXM: none
The 3 least significant bits may be used to match the PCP bits in
an 802.1Q header. Other bits are always zero:
OXM_OF_VLAN_VID
<------------->
5 3
+--------+------+
| zero | PCP |
+--------+------+
0
This field may only be used when vlan_vid is not wildcarded and
does not exact match on 0 (which only matches when there is no
802.1Q header).
See VLAN Comparison Chart, below, for some examples.
Open vSwitch Extension VLAN Field
The vlan_tci extension can describe more kinds of VLAN matches
than the other variants. It is also simpler than the other
variants.
VLAN TCI Field
Name: vlan_tci
Width: 16 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: Ethernet
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: none
NXM: NXM_OF_VLAN_TCI (4) since Open vSwitch 1.1
For a packet without an 802.1Q header, this field is zero. For a
packet with an 802.1Q header, this field is the TCI with the bit
in CFI’s position (marked P for ``present’’ below) forced to 1.
Thus, for a packet in VLAN 9 with priority 7, it has the value
0xf009:
NXM_VLAN_TCI
<---------->
3 1 12
+----+--+----+
|PCP |P |VID |
+----+--+----+
7 1 9
Usage examples:
vlan_tci=0
Match packets without an 802.1Q header.
vlan_tci=0x1000/0x1000
Match packets with an 802.1Q header, regardless of
VLAN and priority values.
vlan_tci=0xf123
Match packets tagged with priority 7 in VLAN 0x123.
vlan_tci=0x1123/0x1fff
Match packets tagged with VLAN 0x123 (and any
priority).
vlan_tci=0x5000/0xf000
Match packets tagged with priority 2 (in any VLAN).
vlan_tci=0/0xfff
Match packets with no 802.1Q header or tagged with
VLAN 0 (and any priority).
vlan_tci=0x5000/0xe000
Match packets with no 802.1Q header or tagged with
priority 2 (in any VLAN).
vlan_tci=0/0xefff
Match packets with no 802.1Q header or tagged with
VLAN 0 and priority 0.
See VLAN Comparison Chart, below, for more examples.
VLAN Comparison Chart
The following table describes each of several possible matching
criteria on 802.1Q header may be expressed with each variation of
the VLAN matching fields:
Criteria OpenFlow 1.0 OpenFlow 1.1 OpenFlow 1.2+ NXM
───────── ───────────── ───────────── ────────────── ──────────
[1] ????/1,??/? ????/1,??/? 0000/0000,-- 0000/0000
[2] ffff/0,??/? ffff/0,??/? 0000/ffff,-- 0000/ffff
[3] 0xxx/0,??/1 0xxx/0,??/1 1xxx/ffff,-- 1xxx/1fff
[4] ????/1,0y/0 fffe/0,0y/0 1000/1000,0y z000/f000
[5] 0xxx/0,0y/0 0xxx/0,0y/0 1xxx/ffff,0y zxxx/ffff
[6] (none) (none) 1001/1001,-- 1001/1001
[7] (none) (none) (none) 3000/3000
[8] (none) (none) (none) 0000/0fff
[9] (none) (none) (none) 0000/f000
[10] (none) (none) (none) 0000/efff
All numbers in the table are expressed in hexadecimal. The
columns in the table are interpreted as follows:
Criteria
See the list below.
OpenFlow 1.0
OpenFlow 1.1
wwww/x,yy/z means VLAN ID match value wwww with
wildcard bit x and VLAN PCP match value yy with
wildcard bit z. ? means that the given bits are
ignored (and conventionally 0 for wwww or yy,
conventionally 1 for x or z). ``(none)’’ means that
OpenFlow 1.0 (or 1.1) cannot match with these
criteria.
OpenFlow 1.2+
xxxx/yyyy,zz means vlan_vid with value xxxx and mask
yyyy, and vlan_pcp (which is not maskable) with value
zz. -- means that vlan_pcp is omitted. ``(none)’’
means that OpenFlow 1.2 cannot match with these
criteria.
NXM xxxx/yyyy means vlan_tci with value xxxx and mask
yyyy.
The matching criteria described by the table are:
[1] Matches any packet, that is, one without an 802.1Q
header or with an 802.1Q header with any TCI value.
[2] Matches only packets without an 802.1Q header.
OpenFlow 1.0 doesn’t define the behavior if dl_vlan
is set to 0xffff and dl_vlan_pcp is not wildcarded.
(Open vSwitch always ignores dl_vlan_pcp when
dl_vlan is set to 0xffff.)
OpenFlow 1.1 says explicitly to ignore dl_vlan_pcp
when dl_vlan is set to 0xffff.
OpenFlow 1.2 doesn’t say how to interpret a match
with vlan_vid value 0 and a mask with
OFPVID_PRESENT (0x1000) set to 1 and some other
bits in the mask set to 1 also. Open vSwitch
interprets it the same way as a mask of 0x1000.
Any NXM match with vlan_tci value 0 and the CFI bit
set to 1 in the mask is equivalent to the one
listed in the table.
[3] Matches only packets that have an 802.1Q header
with VID xxx (and any PCP).
[4] Matches only packets that have an 802.1Q header
with PCP y (and any VID).
OpenFlow 1.0 doesn’t clearly define the behavior
for this case. Open vSwitch implements it this way.
In the NXM value, z equals (y << 1) | 1.
[5] Matches only packets that have an 802.1Q header
with VID xxx and PCP y.
In the NXM value, z equals (y << 1) | 1.
[6] Matches only packets that have an 802.1Q header
with an odd-numbered VID (and any PCP). Only
possible with OpenFlow 1.2 and NXM. (This is just
an example; one can match on any desired VID bit
pattern.)
[7] Matches only packets that have an 802.1Q header
with an odd-numbered PCP (and any VID). Only
possible with NXM. (This is just an example; one
can match on any desired VID bit pattern.)
[8] Matches packets with no 802.1Q header or with an
802.1Q header with a VID of 0. Only possible with
NXM.
[9] Matches packets with no 802.1Q header or with an
802.1Q header with a PCP of 0. Only possible with
NXM.
[10] Matches packets with no 802.1Q header or with an
802.1Q header with both VID and PCP of 0. Only
possible with NXM.
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
─────────── ──────────────── ───── ──── ──────── ──────────────────────
mpls_label 4 (low 20 bits) no yes MPLS OF 1.2+ and OVS 1.11+
mpls_tc 1 (low 3 bits) no yes MPLS OF 1.2+ and OVS 1.11+
mpls_bos 1 (low 1 bits) no no MPLS OF 1.3+ and OVS 1.11+
mpls_ttl 1 no yes MPLS OVS 2.6+
One or more MPLS headers (more commonly called MPLS labels)
follow an Ethernet type field that specifies an MPLS Ethernet
type [RFC 3032]. Ethertype 0x8847 is used for all unicast.
Multicast MPLS is divided into two specific classes, one of which
uses Ethertype 0x8847 and the other 0x8848 [RFC 5332].
The most common overall packet format is Ethernet II, shown below
(SNAP encapsulation may be used but is not ordinarily seen in
Ethernet networks):
Ethernet MPLS
<------------> <------------>
48 48 16 20 3 1 8
+---+---+------+ +-----+--+-+---+
|dst|src| type | |label|TC|S|TTL| ...
+---+---+------+ +-----+--+-+---+
0x8847
MPLS can be encapsulated inside an 802.1Q header, in which case
the combination looks like this:
Ethernet 802.1Q Ethertype MPLS
<------> <--------> <-------> <------------>
48 48 16 16 16 20 3 1 8
+----+---+ +------+---+ +---------+ +-----+--+-+---+
|dst |src| | TPID |TCI| | type | |label|TC|S|TTL| ...
+----+---+ +------+---+ +---------+ +-----+--+-+---+
0x8100 0x8847
The fields within an MPLS label are:
Label, 20 bits.
An identifier.
Traffic control (TC), 3 bits.
Used for quality of service.
Bottom of stack (BOS), 1 bit (labeled just ``S’’ above).
0 indicates that another MPLS label follows this
one.
1 indicates that this MPLS label is the last one in
the stack, so that some other protocol follows this
one.
Time to live (TTL), 8 bits.
Each hop across an MPLS network decrements the TTL
by 1. If it reaches 0, the packet is discarded.
OpenFlow does not make the MPLS TTL available as a
match field, but actions are available to set and
decrement the TTL. Open vSwitch 2.6 and later makes
the MPLS TTL available as an extension.
MPLS Label Stacks
Unlike the other encapsulations supported by OpenFlow and Open
vSwitch, MPLS labels are routinely used in ``stacks’’ two or
three deep and sometimes even deeper. Open vSwitch currently
supports up to three labels.
The OpenFlow specification only supports matching on the
outermost MPLS label at any given time. To match on the second
label, one must first ``pop’’ the outer label and advance to
another OpenFlow table, where the inner label may be matched. To
match on the third label, one must pop the two outer labels, and
so on.
MPLS Inner Protocol
Unlike all other forms of encapsulation that Open vSwitch and
OpenFlow support, an MPLS label does not indicate what inner
protocol it encapsulates. Different deployments determine the
inner protocol in different ways [RFC 3032]:
• A few reserved label values do indicate an inner
protocol. Label 0, the ``IPv4 Explicit NULL
Label,’’ indicates inner IPv4. Label 2, the ``IPv6
Explicit NULL Label,’’ indicates inner IPv6.
• Some deployments use a single inner protocol
consistently.
• In some deployments, the inner protocol must be
inferred from the innermost label.
• In some deployments, the inner protocol must be
inferred from the innermost label and the
encapsulated data, e.g. to distinguish between
inner IPv4 and IPv6 based on whether the first
nibble of the inner protocol data are 4 or 6.
OpenFlow and Open vSwitch do not currently support
these cases.
Open vSwitch and OpenFlow do not infer the inner protocol, even
if reserved label values are in use. Instead, the flow table must
specify the inner protocol at the time it pops the bottommost
MPLS label, using the Ethertype argument to the pop_mpls action.
Field Details
MPLS Label Field
Name: mpls_label
Width: 32 bits (only the least-significant 20 bits may be nonzero)
Format: decimal
Masking: not maskable
Prerequisites: MPLS
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_MPLS_LABEL (34) since OpenFlow 1.2 and Open vSwitch
1.11
NXM: none
The least significant 20 bits hold the ``label’’ field from the
MPLS label. Other bits are zero:
OXM_OF_MPLS_LABEL
<--------------->
12 20
+--------+--------+
| zero | label |
+--------+--------+
0
Most label values are available for any use by deployments.
Values under 16 are reserved.
MPLS Traffic Class Field
Name: mpls_tc
Width: 8 bits (only the least-significant 3 bits may be nonzero)
Format: decimal
Masking: not maskable
Prerequisites: MPLS
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_MPLS_TC (35) since OpenFlow 1.2 and Open vSwitch
1.11
NXM: none
The least significant 3 bits hold the TC field from the MPLS
label. Other bits are zero:
OXM_OF_MPLS_TC
<------------>
5 3
+--------+-----+
| zero | TC |
+--------+-----+
0
This field is intended for use for Quality of Service (QoS) and
Explicit Congestion Notification purposes, but its particular
interpretation is deployment specific.
Before 2009, this field was named EXP and reserved for
experimental use [RFC 5462].
MPLS Bottom of Stack Field
Name: mpls_bos
Width: 8 bits (only the least-significant 1 bits may be nonzero)
Format: decimal
Masking: not maskable
Prerequisites: MPLS
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_MPLS_BOS (36) since OpenFlow 1.3 and Open vSwitch
1.11
NXM: none
The least significant bit holds the BOS field from the MPLS
label. Other bits are zero:
OXM_OF_MPLS_BOS
<------------->
7 1
+--------+------+
| zero | BOS |
+--------+------+
0
This field is useful as part of processing a series of incoming
MPLS labels. A flow that includes a pop_mpls action should
generally match on mpls_bos:
• When mpls_bos is 0, there is another MPLS label
following this one, so the Ethertype passed to
pop_mpls should be an MPLS Ethertype. For example:
table=0, dl_type=0x8847, mpls_bos=0,
actions=pop_mpls:0x8847, goto_table:1
• When mpls_bos is 1, this MPLS label is the last
one, so the Ethertype passed to pop_mpls should be
a non-MPLS Ethertype such as IPv4. For example:
table=1, dl_type=0x8847, mpls_bos=1,
actions=pop_mpls:0x0800, goto_table:2
MPLS Time-to-Live Field
Name: mpls_ttl
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: MPLS
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_MPLS_TTL (30) since Open vSwitch 2.6
Holds the 8-bit time-to-live field from the MPLS label:
NXM_NX_MPLS_TTL
<------------->
8
+---------------+
| TTL |
+---------------+
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
────────────────────── ──────────────── ───── ──── ────────── ─────────────────────
ip_src aka nw_src 4 yes yes IPv4 OF 1.2+ and OVS 1.1+
ip_dst aka nw_dst 4 yes yes IPv4 OF 1.2+ and OVS 1.1+
ipv6_src 16 yes yes IPv6 OF 1.2+ and OVS 1.1+
ipv6_dst 16 yes yes IPv6 OF 1.2+ and OVS 1.1+
ipv6_label 4 (low 20 bits) yes yes IPv6 OF 1.2+ and OVS 1.4+
nw_proto aka ip_proto 1 no no IPv4/IPv6 OF 1.2+ and OVS 1.1+
nw_ttl 1 no yes IPv4/IPv6 OVS 1.4+
ip_frag aka nw_frag 1 (low 2 bits) yes no IPv4/IPv6 OVS 1.3+
nw_tos 1 no yes IPv4/IPv6 OVS 1.1+
ip_dscp 1 (low 6 bits) no yes IPv4/IPv6 OF 1.2+ and OVS 1.7+
nw_ecn aka ip_ecn 1 (low 2 bits) no yes IPv4/IPv6 OF 1.2+ and OVS 1.4+
IPv4 Specific Fields
These fields are applicable only to IPv4 flows, that is, flows
that match on the IPv4 Ethertype 0x0800.
IPv4 Source Address Field
Name: ip_src (aka nw_src)
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: IPv4
Access: read/write
OpenFlow 1.0: yes (CIDR match only)
OpenFlow 1.1: yes
OXM: OXM_OF_IPV4_SRC (11) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_IP_SRC (7) since Open vSwitch 1.1
The source address from the IPv4 header:
Ethernet IPv4
<-----------> <--------------->
48 48 16 8 32 32
+---+---+-----+ +---+-----+---+---+
|dst|src|type | |...|proto|src|dst| ...
+---+---+-----+ +---+-----+---+---+
0x800
For historical reasons, in an ARP or RARP flow, Open vSwitch
interprets matches on nw_src as actually referring to the ARP
SPA.
IPv4 Destination Address Field
Name: ip_dst (aka nw_dst)
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: IPv4
Access: read/write
OpenFlow 1.0: yes (CIDR match only)
OpenFlow 1.1: yes
OXM: OXM_OF_IPV4_DST (12) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_IP_DST (8) since Open vSwitch 1.1
The destination address from the IPv4 header:
Ethernet IPv4
<-----------> <--------------->
48 48 16 8 32 32
+---+---+-----+ +---+-----+---+---+
|dst|src|type | |...|proto|src|dst| ...
+---+---+-----+ +---+-----+---+---+
0x800
For historical reasons, in an ARP or RARP flow, Open vSwitch
interprets matches on nw_dst as actually referring to the ARP
TPA.
IPv6 Specific Fields
These fields apply only to IPv6 flows, that is, flows that match
on the IPv6 Ethertype 0x86dd.
IPv6 Source Address Field
Name: ipv6_src
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: IPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_IPV6_SRC (26) since OpenFlow 1.2 and Open
vSwitch 1.1
NXM: NXM_NX_IPV6_SRC (19) since Open vSwitch 1.1
The source address from the IPv6 header:
Ethernet IPv6
<------------> <-------------->
48 48 16 8 128 128
+---+---+------+ +---+----+---+---+
|dst|src| type | |...|next|src|dst| ...
+---+---+------+ +---+----+---+---+
0x86dd
Open vSwitch 1.8 added support for bitwise matching; earlier
versions supported only CIDR masks.
IPv6 Destination Address Field
Name: ipv6_dst
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: IPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_IPV6_DST (27) since OpenFlow 1.2 and Open
vSwitch 1.1
NXM: NXM_NX_IPV6_DST (20) since Open vSwitch 1.1
The destination address from the IPv6 header:
Ethernet IPv6
<------------> <-------------->
48 48 16 8 128 128
+---+---+------+ +---+----+---+---+
|dst|src| type | |...|next|src|dst| ...
+---+---+------+ +---+----+---+---+
0x86dd
Open vSwitch 1.8 added support for bitwise matching; earlier
versions supported only CIDR masks.
IPv6 Flow Label Field
Name: ipv6_label
Width: 32 bits (only the least-significant 20 bits may be nonzero)
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: IPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_IPV6_FLABEL (28) since OpenFlow 1.2 and Open vSwitch
1.7
NXM: NXM_NX_IPV6_LABEL (27) since Open vSwitch 1.4
The least significant 20 bits hold the flow label field from the
IPv6 header. Other bits are zero:
OXM_OF_IPV6_FLABEL
<---------------->
12 20
+--------+---------+
| zero | label |
+--------+---------+
0
IPv4/IPv6 Fields
These fields exist with at least approximately the same meaning
in both IPv4 and IPv6, so they are treated as a single field for
matching purposes. Any flow that matches on the IPv4 Ethertype
0x0800 or the IPv6 Ethertype 0x86dd may match on these fields.
IPv4/v6 Protocol Field
Name: nw_proto (aka ip_proto)
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: IPv4/IPv6
Access: read-only
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_IP_PROTO (10) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_IP_PROTO (6) since Open vSwitch 1.1
Matches the IPv4 or IPv6 protocol type.
For historical reasons, in an ARP or RARP flow, Open vSwitch
interprets matches on nw_proto as actually referring to the ARP
opcode. The ARP opcode is a 16-bit field, so for matching
purposes ARP opcodes greater than 255 are treated as 0; this
works adequately because in practice ARP and RARP only use
opcodes 1 through 4.
In the case of fragmented traffic, a difference exists in the way
the field acts for IPv4 and IPv6 later fragments. For IPv6
fragments with nonzero offset, nw_proto is set to the IPv6
protocol type for fragments (44). Conversely, for IPv4 later
fragments, the field is set based on the protocol type present in
the header.
IPv4/v6 TTL/Hop Limit Field
Name: nw_ttl
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: IPv4/IPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_IP_TTL (29) since Open vSwitch 1.4
The main reason to match on the TTL or hop limit field is to
detect whether a dec_ttl action will fail due to a TTL exceeded
error. Another way that a controller can detect TTL exceeded is
to listen for OFPR_INVALID_TTL ``packet-in’’ messages via
OpenFlow.
IPv4/v6 Fragment Bitmask Field
Name: ip_frag (aka nw_frag)
Width: 8 bits (only the least-significant 2 bits may be nonzero)
Format: frag
Masking: arbitrary bitwise masks
Prerequisites: IPv4/IPv6
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXM_NX_IP_FRAG (26) since Open vSwitch 1.3
Specifies what kinds of IP fragments or non-fragments to match.
The value for this field is most conveniently specified as one of
the following:
no Match only non-fragmented packets.
yes Matches all fragments.
first Matches only fragments with offset 0.
later Matches only fragments with nonzero offset.
not_later
Matches non-fragmented packets and fragments with
zero offset.
The field is internally formatted as 2 bits: bit 0 is 1 for an IP
fragment with any offset (and otherwise 0), and bit 1 is 1 for an
IP fragment with nonzero offset (and otherwise 0), like so:
NXM_NX_IP_FRAG
<------------>
6 1 1
+----+-----+---+
|zero|later|any|
+----+-----+---+
0
Even though 2 bits have 4 possible values, this field only uses 3
of them:
• A packet that is not an IP fragment has value 0.
• A packet that is an IP fragment with offset 0 (the
first fragment) has bit 0 set and thus value 1.
• A packet that is an IP fragment with nonzero offset
has bits 0 and 1 set and thus value 3.
The switch may reject matches against values that can never
appear.
It is important to understand how this field interacts with the
OpenFlow fragment handling mode:
• In OFPC_FRAG_DROP mode, the OpenFlow switch drops
all IP fragments before they reach the flow table,
so every packet that is available for matching will
have value 0 in this field.
• Open vSwitch does not implement OFPC_FRAG_REASM
mode, but if it did then IP fragments would be
reassembled before they reached the flow table and
again every packet available for matching would
always have value 0.
• In OFPC_FRAG_NORMAL mode, all three values are
possible, but OpenFlow 1.0 says that fragments’
transport ports are always 0, even for the first
fragment, so this does not provide much extra
information.
• In OFPC_FRAG_NX_MATCH mode, all three values are
possible. For fragments with offset 0, Open vSwitch
makes L4 header information available.
Thus, this field is likely to be most useful for an Open vSwitch
switch configured in OFPC_FRAG_NX_MATCH mode. See the description
of the set-frags command in ovs-ofctl(8), for more details.
IPv4/IPv6 TOS Fields
IPv4 and IPv6 contain a one-byte ``type of service’’ or TOS field
that has the following format:
type of service
<------------->
6 2
+--------+------+
| DSCP | ECN |
+--------+------+
IPv4/v6 DSCP (Bits 2-7) Field
Name: nw_tos
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: IPv4/IPv6
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: none
NXM: NXM_OF_IP_TOS (5) since Open vSwitch 1.1
This field is the TOS byte with the two ECN bits cleared to 0:
NXM_OF_IP_TOS
<----------->
6 2
+------+------+
| DSCP | zero |
+------+------+
0
IPv4/v6 DSCP (Bits 0-5) Field
Name: ip_dscp
Width: 8 bits (only the least-significant 6 bits may be nonzero)
Format: decimal
Masking: not maskable
Prerequisites: IPv4/IPv6
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_IP_DSCP (8) since OpenFlow 1.2 and Open vSwitch
1.7
NXM: none
This field is the TOS byte shifted right to put the DSCP bits in
the 6 least-significant bits:
OXM_OF_IP_DSCP
<------------>
2 6
+-------+------+
| zero | DSCP |
+-------+------+
0
IPv4/v6 ECN Field
Name: nw_ecn (aka ip_ecn)
Width: 8 bits (only the least-significant 2 bits may be nonzero)
Format: decimal
Masking: not maskable
Prerequisites: IPv4/IPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_IP_ECN (9) since OpenFlow 1.2 and Open vSwitch 1.7
NXM: NXM_NX_IP_ECN (28) since Open vSwitch 1.4
This field is the TOS byte with the DSCP bits cleared to 0:
OXM_OF_IP_ECN
<----------->
6 2
+-------+-----+
| zero | ECN |
+-------+-----+
0
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
──────── ────── ───── ──── ──────── ─────────────────────
arp_op 2 no yes ARP OF 1.2+ and OVS 1.1+
arp_spa 4 yes yes ARP OF 1.2+ and OVS 1.1+
arp_tpa 4 yes yes ARP OF 1.2+ and OVS 1.1+
arp_sha 6 yes yes ARP OF 1.2+ and OVS 1.1+
arp_tha 6 yes yes ARP OF 1.2+ and OVS 1.1+
In theory, Address Resolution Protocol, or ARP, is a generic
protocol generic protocol that can be used to obtain the hardware
address that corresponds to any higher-level protocol address. In
contemporary usage, ARP is used only in Ethernet networks to
obtain the Ethernet address for a given IPv4 address. OpenFlow
and Open vSwitch only support this usage of ARP. For this use
case, an ARP packet has the following format, with the ARP fields
exposed as Open vSwitch fields highlighted:
Ethernet ARP
<-----------> <---------------------------------->
48 48 16 16 16 8 8 16 48 32 48 32
+---+---+-----+ +---+-----+---+---+--+---+---+---+---+
|dst|src|type | |hrd| pro |hln|pln|op|sha|spa|tha|tpa|
+---+---+-----+ +---+-----+---+---+--+---+---+---+---+
0x806 1 0x800 6 4
The ARP fields are also used for RARP, the Reverse Address
Resolution Protocol, which shares ARP’s wire format.
ARP Opcode Field
Name: arp_op
Width: 16 bits
Format: decimal
Masking: not maskable
Prerequisites: ARP
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_ARP_OP (21) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_ARP_OP (15) since Open vSwitch 1.1
Even though this is a 16-bit field, Open vSwitch does not support
ARP opcodes greater than 255; it treats them to zero. This works
adequately because in practice ARP and RARP only use opcodes 1
through 4.
ARP Source IPv4 Address Field
Name: arp_spa
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: ARP
Access: read/write
OpenFlow 1.0: yes (CIDR match only)
OpenFlow 1.1: yes
OXM: OXM_OF_ARP_SPA (22) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_ARP_SPA (16) since Open vSwitch 1.1
ARP Target IPv4 Address Field
Name: arp_tpa
Width: 32 bits
Format: IPv4
Masking: arbitrary bitwise masks
Prerequisites: ARP
Access: read/write
OpenFlow 1.0: yes (CIDR match only)
OpenFlow 1.1: yes
OXM: OXM_OF_ARP_TPA (23) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_ARP_TPA (17) since Open vSwitch 1.1
ARP Source Ethernet Address Field
Name: arp_sha
Width: 48 bits
Format: Ethernet
Masking: arbitrary bitwise masks
Prerequisites: ARP
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_ARP_SHA (24) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_NX_ARP_SHA (17) since Open vSwitch 1.1
ARP Target Ethernet Address Field
Name: arp_tha
Width: 48 bits
Format: Ethernet
Masking: arbitrary bitwise masks
Prerequisites: ARP
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_ARP_THA (25) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_NX_ARP_THA (18) since Open vSwitch 1.1
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
───────────────── ──────────────── ───── ──── ──────── ────────────────
nsh_flags 1 yes yes NSH OVS 2.8+
nsh_ttl 1 no yes NSH OVS 2.9+
nsh_mdtype 1 no no NSH OVS 2.8+
nsh_np 1 no no NSH OVS 2.8+
nsh_spi aka nsp 4 (low 24 bits) no yes NSH OVS 2.8+
nsh_si aka nsi 1 no yes NSH OVS 2.8+
nsh_c1 aka nshc1 4 yes yes NSH OVS 2.8+
nsh_c2 aka nshc2 4 yes yes NSH OVS 2.8+
nsh_c3 aka nshc3 4 yes yes NSH OVS 2.8+
nsh_c4 aka nshc4 4 yes yes NSH OVS 2.8+
Service functions are widely deployed and essential in many
networks. These service functions provide a range of features
such as security, WAN acceleration, and server load balancing.
Service functions may be instantiated at different points in the
network infrastructure such as the wide area network, data
center, and so forth.
Prior to development of the SFC architecture [RFC 7665] and the
protocol specified in this document, current service function
deployment models have been relatively static and bound to
topology for insertion and policy selection. Furthermore, they do
not adapt well to elastic service environments enabled by
virtualization.
New data center network and cloud architectures require more
flexible service function deployment models. Additionally, the
transition to virtual platforms demands an agile service
insertion model that supports dynamic and elastic service
delivery. Specifically, the following functions are necessary:
1. The movement of service functions and application
workloads in the network.
2. The ability to easily bind service policy to granular
information, such as per-subscriber state.
3. The capability to steer traffic to the requisite
service function(s).
The Network Service Header (NSH) specification defines a new data
plane protocol, which is an encapsulation for service function
chains. The NSH is designed to encapsulate an original packet or
frame, and in turn be encapsulated by an outer transport
encapsulation (which is used to deliver the NSH to NSH-aware
network elements), as shown below:
+-----------------------+----------------------------+---------------------+
|Transport Encapsulation|Network Service Header (NSH)|Original Packet/Frame|
+-----------------------+----------------------------+---------------------+
The NSH is composed of the following elements:
1. Service Function Path identification.
2. Indication of location within a Service Function Path.
3. Optional, per packet metadata (fixed length or
variable).
[RFC 7665] provides an overview of a service chaining
architecture that clearly defines the roles of the various
elements and the scope of a service function chaining
encapsulation. Figure 3 of [RFC 7665] depicts the SFC
architectural components after classification. The NSH is the SFC
encapsulation referenced in [RFC 7665].
flags field (2 bits) Field
Name: nsh_flags
Width: 8 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_FLAGS (1) since Open vSwitch 2.8
TTL field (6 bits) Field
Name: nsh_ttl
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_TTL (10) since Open vSwitch 2.9
mdtype field (8 bits) Field
Name: nsh_mdtype
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: NSH
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_MDTYPE (2) since Open vSwitch 2.8
np (next protocol) field (8 bits) Field
Name: nsh_np
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: NSH
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_NP (3) since Open vSwitch 2.8
spi (service path identifier) field (24 bits) Field
Name: nsh_spi (aka nsp)
Width: 32 bits (only the least-significant 24 bits may be nonzero)
Format: hexadecimal
Masking: not maskable
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_SPI (4) since Open vSwitch 2.8
si (service index) field (8 bits) Field
Name: nsh_si (aka nsi)
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_SI (5) since Open vSwitch 2.8
c1 (Network Platform Context) field (32 bits) Field
Name: nsh_c1 (aka nshc1)
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_C1 (6) since Open vSwitch 2.8
c2 (Network Shared Context) field (32 bits) Field
Name: nsh_c2 (aka nshc2)
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_C2 (7) since Open vSwitch 2.8
c3 (Service Platform Context) field (32 bits) Field
Name: nsh_c3 (aka nshc3)
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_C3 (8) since Open vSwitch 2.8
c4 (Service Shared Context) field (32 bits) Field
Name: nsh_c4 (aka nshc4)
Width: 32 bits
Format: hexadecimal
Masking: arbitrary bitwise masks
Prerequisites: NSH
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: NXOXM_NSH_C4 (9) since Open vSwitch 2.8
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
─────────────────── ──────────────── ───── ──── ──────── ─────────────────────
tcp_src aka tp_src 2 yes yes TCP OF 1.2+ and OVS 1.1+
tcp_dst aka tp_dst 2 yes yes TCP OF 1.2+ and OVS 1.1+
tcp_flags 2 (low 12 bits) yes no TCP OF 1.3+ and OVS 2.1+
udp_src 2 yes yes UDP OF 1.2+ and OVS 1.1+
udp_dst 2 yes yes UDP OF 1.2+ and OVS 1.1+
sctp_src 2 yes yes SCTP OF 1.2+ and OVS 2.0+
sctp_dst 2 yes yes SCTP OF 1.2+ and OVS 2.0+
For matching purposes, no distinction is made whether these
protocols are encapsulated within IPv4 or IPv6.
TCP
The following diagram shows TCP within IPv4. Open vSwitch also
supports TCP in IPv6. Only TCP fields implemented as Open vSwitch
fields are shown:
Ethernet IPv4 TCP
<-----------> <---------------> <------------------->
48 48 16 8 32 32 16 16 12
+---+---+-----+ +---+-----+---+---+ +---+---+---+-----+---+
|dst|src|type | |...|proto|src|dst| |src|dst|...|flags|...| ...
+---+---+-----+ +---+-----+---+---+ +---+---+---+-----+---+
0x800 6
TCP Source Port Field
Name: tcp_src (aka tp_src)
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: TCP
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_TCP_SRC (13) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_TCP_SRC (9) since Open vSwitch 1.1
Open vSwitch 1.6 added support for bitwise matching.
TCP Destination Port Field
Name: tcp_dst (aka tp_dst)
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: TCP
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_TCP_DST (14) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_TCP_DST (10) since Open vSwitch 1.1
Open vSwitch 1.6 added support for bitwise matching.
TCP Flags Field
Name: tcp_flags
Width: 16 bits (only the least-significant 12 bits may be nonzero)
Format: TCP flags
Masking: arbitrary bitwise masks
Prerequisites: TCP
Access: read-only
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: ONFOXM_ET_TCP_FLAGS (42) since OpenFlow 1.3 and Open
vSwitch 2.4; OXM_OF_TCP_FLAGS (42) since OpenFlow 1.5 and
Open vSwitch 2.3
NXM: NXM_NX_TCP_FLAGS (34) since Open vSwitch 2.1
This field holds the TCP flags. TCP currently defines 9 flag
bits. An additional 3 bits are reserved. For more information,
see [RFC 793], [RFC 3168], and [RFC 3540].
Matches on this field are most conveniently written in terms of
symbolic names (given in the diagram below), each preceded by
either + for a flag that must be set, or - for a flag that must
be unset, without any other delimiters between the flags. Flags
not mentioned are wildcarded. For example, tcp,tcp_flags=+syn-ack
matches TCP SYNs that are not ACKs, and tcp,tcp_flags=+[200]
matches TCP packets with the reserved [200] flag set. Matches can
also be written as flags/mask, where flags and mask are 16-bit
numbers in decimal or in hexadecimal prefixed by 0x.
The flag bits are:
reserved later RFCs RFC 793
<---------------> <--------> <--------------------->
4 1 1 1 1 1 1 1 1 1 1 1 1
+----+-----+-----+-----+--+---+---+---+---+---+---+---+---+
|zero|[800]|[400]|[200]|NS|CWR|ECE|URG|ACK|PSH|RST|SYN|FIN|
+----+-----+-----+-----+--+---+---+---+---+---+---+---+---+
0
UDP
The following diagram shows UDP within IPv4. Open vSwitch also
supports UDP in IPv6. Only UDP fields that Open vSwitch exposes
as fields are shown:
Ethernet IPv4 UDP
<-----------> <---------------> <--------->
48 48 16 8 32 32 16 16
+---+---+-----+ +---+-----+---+---+ +---+---+---+
|dst|src|type | |...|proto|src|dst| |src|dst|...| ...
+---+---+-----+ +---+-----+---+---+ +---+---+---+
0x800 17
UDP Source Port Field
Name: udp_src
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: UDP
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_UDP_SRC (15) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_UDP_SRC (11) since Open vSwitch 1.1
UDP Destination Port Field
Name: udp_dst
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: UDP
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_UDP_DST (16) since OpenFlow 1.2 and Open
vSwitch 1.7
NXM: NXM_OF_UDP_DST (12) since Open vSwitch 1.1
SCTP
The following diagram shows SCTP within IPv4. Open vSwitch also
supports SCTP in IPv6. Only SCTP fields that Open vSwitch exposes
as fields are shown:
Ethernet IPv4 SCTP
<-----------> <---------------> <--------->
48 48 16 8 32 32 16 16
+---+---+-----+ +---+-----+---+---+ +---+---+---+
|dst|src|type | |...|proto|src|dst| |src|dst|...| ...
+---+---+-----+ +---+-----+---+---+ +---+---+---+
0x800 132
SCTP Source Port Field
Name: sctp_src
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: SCTP
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_SCTP_SRC (17) since OpenFlow 1.2 and Open
vSwitch 2.0
NXM: none
SCTP Destination Port Field
Name: sctp_dst
Width: 16 bits
Format: decimal
Masking: arbitrary bitwise masks
Prerequisites: SCTP
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_SCTP_DST (18) since OpenFlow 1.2 and Open
vSwitch 2.0
NXM: none
Summary:
Name Bytes Mask RW? Prereqs NXM/OXM Support
──────────────── ────── ───── ──── ─────────── ─────────────────────
icmp_type 1 no yes ICMPv4 OF 1.2+ and OVS 1.1+
icmp_code 1 no yes ICMPv4 OF 1.2+ and OVS 1.1+
icmpv6_type 1 no yes ICMPv6 OF 1.2+ and OVS 1.1+
icmpv6_code 1 no yes ICMPv6 OF 1.2+ and OVS 1.1+
nd_target 16 yes yes ND OF 1.2+ and OVS 1.1+
nd_sll 6 yes yes ND solicit OF 1.2+ and OVS 1.1+
nd_tll 6 yes yes ND advert OF 1.2+ and OVS 1.1+
nd_reserved 4 no yes ND OVS 2.11+
nd_options_type 1 no yes ND OVS 2.11+
ICMPv4
Ethernet IPv4 ICMPv4
<-----------> <---------------> <----------->
48 48 16 8 32 32 8 8
+---+---+-----+ +---+-----+---+---+ +----+----+---+
|dst|src|type | |...|proto|src|dst| |type|code|...| ...
+---+---+-----+ +---+-----+---+---+ +----+----+---+
0x800 1
ICMPv4 Type Field
Name: icmp_type
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: ICMPv4
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_ICMPV4_TYPE (19) since OpenFlow 1.2 and
Open vSwitch 1.7
NXM: NXM_OF_ICMP_TYPE (13) since Open vSwitch 1.1
For historical reasons, in an ICMPv4 flow, Open vSwitch
interprets matches on tp_src as actually referring to the ICMP
type.
ICMPv4 Code Field
Name: icmp_code
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: ICMPv4
Access: read/write
OpenFlow 1.0: yes (exact match only)
OpenFlow 1.1: yes (exact match only)
OXM: OXM_OF_ICMPV4_CODE (20) since OpenFlow 1.2 and
Open vSwitch 1.7
NXM: NXM_OF_ICMP_CODE (14) since Open vSwitch 1.1
For historical reasons, in an ICMPv4 flow, Open vSwitch
interprets matches on tp_dst as actually referring to the ICMP
code.
ICMPv6
Ethernet IPv6 ICMPv6
<------------> <--------------> <----------->
48 48 16 8 128 128 8 8
+---+---+------+ +---+----+---+---+ +----+----+---+
|dst|src| type | |...|next|src|dst| |type|code|...| ...
+---+---+------+ +---+----+---+---+ +----+----+---+
0x86dd 58
ICMPv6 Type Field
Name: icmpv6_type
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: ICMPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_ICMPV6_TYPE (29) since OpenFlow 1.2 and
Open vSwitch 1.7
NXM: NXM_NX_ICMPV6_TYPE (21) since Open vSwitch 1.1
ICMPv6 Code Field
Name: icmpv6_code
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: ICMPv6
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_ICMPV6_CODE (30) since OpenFlow 1.2 and
Open vSwitch 1.7
NXM: NXM_NX_ICMPV6_CODE (22) since Open vSwitch 1.1
ICMPv6 Neighbor Discovery
Ethernet IPv6 ICMPv6 ICMPv6 ND
<------------> <--------------> <--------------> <--------------->
48 48 16 8 128 128 8 8 128
+---+---+------+ +---+----+---+---+ +-------+----+---+ +------+----------+
|dst|src| type | |...|next|src|dst| | type |code|...| |target|option ...|
+---+---+------+ +---+----+---+---+ +-------+----+---+ +------+----------+
0x86dd 58 135/136 0
ICMPv6 Neighbor Discovery Target IPv6 Field
Name: nd_target
Width: 128 bits
Format: IPv6
Masking: arbitrary bitwise masks
Prerequisites: ND
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_IPV6_ND_TARGET (31) since OpenFlow 1.2
and Open vSwitch 1.7
NXM: NXM_NX_ND_TARGET (23) since Open vSwitch 1.1
ICMPv6 Neighbor Discovery Source Ethernet Address Field
Name: nd_sll
Width: 48 bits
Format: Ethernet
Masking: arbitrary bitwise masks
Prerequisites: ND solicit
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_IPV6_ND_SLL (32) since OpenFlow 1.2 and
Open vSwitch 1.7
NXM: NXM_NX_ND_SLL (24) since Open vSwitch 1.1
ICMPv6 Neighbor Discovery Target Ethernet Address Field
Name: nd_tll
Width: 48 bits
Format: Ethernet
Masking: arbitrary bitwise masks
Prerequisites: ND advert
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: OXM_OF_IPV6_ND_TLL (33) since OpenFlow 1.2 and
Open vSwitch 1.7
NXM: NXM_NX_ND_TLL (25) since Open vSwitch 1.1
ICMPv6 Neighbor Discovery Reserved Field Field
Name: nd_reserved
Width: 32 bits
Format: decimal
Masking: not maskable
Prerequisites: ND
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: ERICOXM_OF_ICMPV6_ND_RESERVED (1) since Open
vSwitch 2.11
This is used to set the R,S,O bits in Neighbor Advertisement
Messages
ICMPv6 Neighbor Discovery Options Type Field Field
Name: nd_options_type
Width: 8 bits
Format: decimal
Masking: not maskable
Prerequisites: ND
Access: read/write
OpenFlow 1.0: not supported
OpenFlow 1.1: not supported
OXM: none
NXM: ERICOXM_OF_ICMPV6_ND_OPTIONS_TYPE (2) since Open
vSwitch 2.11
A value of 1 indicates that the option is Source Link Layer. A
value of 2 indicates that the options is Target Link Layer. See
RFC 4861 for further details.
Casado M. Casado, M. J. Freedman, J. Pettit, J. Luo, N.
McKeown, and S. Shenker, ``Ethane: Taking Control
of the Enterprise,’’ Computer Communications
Review, October 2007.
ERSPAN M. Foschiano, K. Ghosh, M. Mehta, ``Cisco Systems’
Encapsulated Remote Switch Port Analyzer
(ERSPAN),’’ ⟨https://tools.ietf.org/html/
draft-foschiano-erspan-03⟩ .
EXT-56 J. Tonsing, ``Permit one of a set of prerequisites
to apply, e.g. don’t preclude non-Ethernet media,’’
⟨https://rs.opennetworking.org/bugs/browse/EXT-56⟩
(ONF members only).
EXT-112
J. Tourrilhes, ``Support non-Ethernet packets
throughout the pipeline,’’ ⟨https://
rs.opennetworking.org/bugs/browse/EXT-112⟩ (ONF
members only).
EXT-134
J. Tourrilhes, ``Match first nibble of the MPLS
payload,’’ ⟨https://rs.opennetworking.org/bugs/
browse/EXT-134⟩ (ONF members only).
Geneve J. Gross, I. Ganga, and T. Sridhar, editors,
``Geneve: Generic Network Virtualization
Encapsulation,’’ ⟨https://datatracker.ietf.org/doc/
draft-ietf-nvo3-geneve/⟩ .
IEEE OUI
IEEE Standards Association, ``MAC Address Block
Large (MA-L),’’ ⟨https://standards.ieee.org/
develop/regauth/oui/index.html⟩ .
NSH P. Quinn and U. Elzur, editors, ``Network Service
Header,’’ ⟨https://datatracker.ietf.org/doc/
draft-ietf-sfc-nsh/⟩ .
OpenFlow 1.0.1
Open Networking Foundation, ``OpenFlow Switch
Errata, Version 1.0.1,’’ June 2012.
OpenFlow 1.1
OpenFlow Consortium, ``OpenFlow Switch
Specification Version 1.1.0 Implemented (Wire
Protocol 0x02),’’ February 2011.
OpenFlow 1.5
Open Networking Foundation, ``OpenFlow Switch
Specification Version 1.5.0 (Protocol version
0x06),’’ December 2014.
OpenFlow Extensions 1.3.x Package 2
Open Networking Foundation, ``OpenFlow Extensions
1.3.x Package 2,’’ December 2013.
TCP Flags Match Field Extension
Open Networking Foundation, ``TCP flags match field
Extension,’’ December 2014. In [OpenFlow Extensions
1.3.x Package 2].
Pepelnjak
I. Pepelnjak, ``OpenFlow and Fermi Estimates,’’
⟨http://blog.ipspace.net/2013/09/
openflow-and-fermi-estimates.html⟩ .
RFC 793
``Transmission Control Protocol,’’ ⟨http://
www.ietf.org/rfc/rfc793.txt⟩ .
RFC 3032
E. Rosen, D. Tappan, G. Fedorkow, Y. Rekhter, D.
Farinacci, T. Li, and A. Conta, ``MPLS Label Stack
Encoding,’’ ⟨http://www.ietf.org/rfc/rfc3032.txt⟩ .
RFC 3168
K. Ramakrishnan, S. Floyd, and D. Black, ``The
Addition of Explicit Congestion Notification (ECN)
to IP,’’ ⟨https://tools.ietf.org/html/rfc3168⟩ .
RFC 3540
N. Spring, D. Wetherall, and D. Ely, ``Robust
Explicit Congestion Notification (ECN) Signaling
with Nonces,’’ ⟨https://tools.ietf.org/html/
rfc3540⟩ .
RFC 4632
V. Fuller and T. Li, ``Classless Inter-domain
Routing (CIDR): The Internet Address Assignment and
Aggregation Plan,’’ ⟨https://tools.ietf.org/html/
rfc4632⟩ .
RFC 5462
L. Andersson and R. Asati, ``Multiprotocol Label
Switching (MPLS) Label Stack Entry: ``EXP’’ Field
Renamed to ``Traffic Class’’ Field,’’ ⟨http://
www.ietf.org/rfc/rfc5462.txt⟩ .
RFC 6830
D. Farinacci, V. Fuller, D. Meyer, and D. Lewis,
``The Locator/ID Separation Protocol (LISP),’’
⟨http://www.ietf.org/rfc/rfc6830.txt⟩ .
RFC 7348
M. Mahalingam, D. Dutt, K. Duda, P. Agarwal, L.
Kreeger, T. Sridhar, M. Bursell, and C. Wright,
``Virtual eXtensible Local Area Network (VXLAN): A
Framework for Overlaying Virtualized Layer 2
Networks over Layer 3 Networks, ’’ ⟨https://
tools.ietf.org/html/rfc7348⟩ .
RFC 7665
J. Halpern, Ed. and C. Pignataro, Ed., ``Service
Function Chaining (SFC) Architecture,’’ ⟨https://
tools.ietf.org/html/rfc7665⟩ .
Srinivasan
V. Srinivasan, S. Suriy, and G. Varghese, ``Packet
Classification using Tuple Space Search,’’ SIGCOMM
1999.
Pagiamtzis
K. Pagiamtzis and A. Sheikholeslami, ``Content-
addressable memory (CAM) circuits and
architectures: A tutorial and survey,’’ IEEE
Journal of Solid-State Circuits, vol. 41, no. 3,
pp. 712-727, March 2006.
VXLAN Group Policy Option
M. Smith and L. Kreeger, `` VXLAN Group Policy
Option.’’ Internet-Draft. ⟨https://tools.ietf.org/
html/draft-smith-vxlan-group-policy⟩ .
Ben Pfaff, with advice from Justin Pettit and Jean Tourrilhes.
This page is part of the Open vSwitch (a distributed virtual
multilayer switch) project. Information about the project can be
found at ⟨http://openvswitch.org/⟩. If you have a bug report for
this manual page, send it to bugs@openvswitch.org. This page was
obtained from the project's upstream Git repository
⟨https://github.com/openvswitch/ovs.git⟩ on 2024-06-14. (At that
time, the date of the most recent commit that was found in the
repository was 2024-06-07.) If you discover any rendering
problems in this HTML version of the page, or you believe there
is a better or more up-to-date source for the page, or you have
corrections or improvements to the information in this COLOPHON
(which is not part of the original manual page), send a mail to
man-pages@man7.org
Open vSwitch 3.2.90 ovs-fields(7)
Pages that refer to this page: ovs-vswitchd.conf.db(5), ovn-architecture(7), ovs-actions(7), ovn-trace(8), ovs-ofctl(8)
|
HTML rendering created 2024-06-26 by Michael Kerrisk, author of The Linux Programming Interface. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH. |
|